This fixes crash in interface_start caused by freeing interface in
interface_free without stopping a timeout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So here is another round of improvements for MT7620 WiFi.
This commit fixes a few significant issues related to TX_PWR_CFG_x and
TX_ALC and also makes the code more readable by adding register
descriptions for things added for MT7620 and use the usual bit-field
access macros and the now defined macros instead of plain bit-ops and
magic numbers.
Properly describe EEPROM_TARGET_POWER at word 0x68 (== byte 0xD0) and
thereby fix internal TXALC which would otherwise just read
out-of-bounds of the EEPROM map.
Split-out tx-power/ALC related stuff into an additional function.
Fix VCO calibration, it was carried out properly in the channel
switching but incomplete in the actual VCO calibration function.
Also there is no need to trigger VCO calibration in channel switching,
the VCO calibration function is already being called at this point.
Remove it from channel switching function to avoid redundant code.
The TX power calibration differs significantly from all other
Mediatek/Ralink chips: They finally allow 0.5dB steps stored as 8-bit
values for (almost) each bitrate -- and promptly ran out of space and
for some reason didn't want to change the EEPROM layout. The hence
opted for a scheme of sharing values for some adjecent bitrates and
a highly over-complicated (or obfuscated?) way to populate the
TX_PWR_CFG_x registers with the values stored in the EEPROM.
The code here now looks much less complicated than what you see in the
vendor's driver, however, it does the exact same thing:
bGpwrdeltaMinus is a constant and always TRUE, hence half of the
code was dead. Gpwrdelta is always 0 (rather than using the value read
from the EEPROM). What remains is some very grotesque effort to avoid
0x20, probably some hardware bug related to some misunderstanding of
what a singed 8-bit value is (imagine: if it was a signed 6-bit value
then someone could believe that 0x20 == 0x0). And then they didn't
clean it up once they later on anandonned that whole story of having a
constant offset for 40 MHz channels and just set the offset to be
constant 0 -- there is no effort for avoiding 0x20 for the 20 MHz
values stored in the EEPROM, hence that's probably just a forbidden
value in the EEPROM specs and won't appear anyway...
Anyway, the whole thing felt like solving some college math test
where in the end everything cancels out and the result equals 0 ;)
To make sure that channel bandwidth power compensation really doesn't
need to be taken care of, output a warning when the corresponding
value stored in the EEPROM is non-zero.
Also there is no apparent reason to refrain from initializing RFCSR
register 13, it doesn't fail what-so-ever.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
RFC 6761 defines a number of top level domains should not be forwarded
to the Internet's domain servers since they are not responsible for
those domains.
This change adds a list of domains that will be blocked when 'boguspriv'
is used and augments that which is already blocked by dnsmasq's notion
of 'local service' using '--bogus-priv' i.e. RFC 1918 private addresses
and IPv6 prefixes as defined in RFC 6303.
To make this configurable rather than hard coded in dnsmasq's init
script, a new file /usr/share/dnsmasq/rfc6761.conf is conditionally
included.
The default file matches the RFC 6761 recommendation along with a few
other top level domains that should not be forwarded to the Internet.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Change dts file to add default sata trigger to sata led.
Backport upstream accepted patch to add sata trigger to device tree
source files already upstreamed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[backport upstream accepted patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.
CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04
UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX
Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.
The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)
To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:
VR9 # setenv loadaddr 0xB0040000
VR9 # setenv f_upgrade_addr 0xB0040000
VR9 # setenv f_upgrade2_addr 0xB0040000
VR9 # saveenv
Then flash the firmware image:
VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
VR9 # erase B0040000 +${filesize}
VR9 # cp.b 0x81000000 0xB0040000 ${filesize}
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
The ugps tool expects device path in last argument. If it's provided
before other options, they won't be processed at all.
Additionally, make it possible to use absolute path for gps character
device in related uci configuration.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This backports fixes for setting of_node and making it possible to read
extra info from DT. This was partially fixed by:
[PATCH] leds: leds-gpio: Set of_node for created LED devices
but it didn't work during initialization.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
continue work started here: http://patchwork.ozlabs.org/patch/520859
Extend /etc/config/system with parameters to set the default respawn treshold and respawn timeout
for procd launched services that have respawn enabled.
This results in cleaner init scripts, while making sure services have respawn parameters set.
Signed-off-by: Claudiu Brasovean <cbrasho@gmail.com>
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If ehci platform driver is loaded before the chipidea controller driver,
both are competing for the same IO resources and the generic driver gets
used for the hardware. This results in USB device mode being
unavailable.
Split generic EHCI support code out of kmod-usb2, so that the chipidea
driver can be included without also pulling in the generic one. Also
rework the load order, so that the chipidea driver gets loaded first, in
case both are installed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Honour the parent interfaces peerdns option when spawning a virtual DHCPv6
interface in order to avoid pulling in IPv6 DNS servers when the user opted
to inhibit peer DNS servers in the configuration.
Fixes#597.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8f218f5 procd: service gets deleted when its last instance is freed
35209a0 procd: update modprobe path
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest Git in order to import the following fixes:
19070b6 unarchive: fix possible segmentation fault in deb_extract()
758527e pkg: forward "provided_by_hand" flag in pkg_merge()
1fdc2ca pkg: mark bit fields in pkg_t unsigned
15fc1ee opkg_cmd: avoid null pointer dereference in opkg_what_depends_conflicts_cmd()
439c89e opkg_cmd: fix endless loop in whatprovides/whatreplaces
0fb3e9f pkg_depends: propagate virtual provided detail flag to providers
793155f pkg_depends: fix unsatisfied dependency installation order
b1dc770 libopkg: fix some overly aggressive line wrapping in pkg_depends.c
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The malta "be" and "le" subtargets share the arch with many devices of
ar71xx and ramips. They can be handy for testing, debugging, trying
both snapshot and release builds.
This commit makes the "be" subtarget part of the ci and release builds
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
We need to let external toolchains be able to specify the path and
specification file to the libthread-db POSIX thread debugging shared
libraries.
This fixes GDB not being able to be installed because it is depending on
libthread-db:
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies
* for gdb:
* libthread-db *
* opkg_install_cmd: Cannot install package gdb.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.9.y
- Remove led1 from diag.sh for RPi3 since it causes boot issues.
- Fix modules.mk typos.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Bump kernel from 4.4.50 to 4.4.52
Refresh patches
Compile tested all 4.4. targets
Run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The current way of creating a STAMP_CONFIGURED filename for OpenSSL can
lead to an extremely long filename that makes touch unable to create it,
and fail the build.
Use mkhash to produce a hash against OPENSSL_OPTIONS which creates a
shortert stamp file,
Fixes#572
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pass down TARGET_CPPFLAGS for path to header files, and append the
libraries we depend on in TARGET_LDFLAGS. Put TARGET_LDFLAGS at the end
of the command line as is required by modern GCC/binutils.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes build issues with external toolchains that do not have STAGING_DIR
in their default search path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes linking failures observed with external toolchains:
/home/florian/dev/toolchains/stbgcc-4.8-1.5/bin/../lib/gcc/mipsel-linux-gnu/4.8.5/../../../../mipsel-linux-gnu/bin/ld:
warning: libubox.so, needed by
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so,
not found (try using -rpath or -rpath-link)
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_open_nested'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_parse'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blob_nest_end'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_add_field'
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
