configure enables libzfs support on default.
This will break the build, on systems without libzfs.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
SVN-Revision: 41935
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41930
* set the system time/data
* "ubus call gps info" will tell you lattitude, longitude, elevation, speed and bearing
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41929
This add 5GHz support for N-PHY to b43, thanks Rafał Miłecki.
b43_wflush16 was put into an extra function because it is pretty big in asm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41900
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41899
The package supports Generic Routing Encapsulation support by registering following protocol kinds:
-gre
-gretap
-grev6
-grev6tap
Following options are valid for gre and gretap kinds:
-ipaddr
-peeraddr
-df
-mtu
-ttl
-tunlink
-zone
-ikey
-okey
-icsum
-ocsum
-iseqno
-oseqno
The gretap kind supports additionally the network option
Following options are valid for grev6 and grev6tap kinds:
-ip6addr
-peer6addr
-weakif
-mtu
-ttl
-tunlink
-zone
-ikey
-okey
-icsum
-ocsum
-iseqno
-oseqno
The grev6tap kind supports additionally the network option
Typical network config for a GREv4 tunnel :
config interface 'gre'
option peeraddr '172.16.18.240'
option mtu '1400'
option proto 'gre'
option tunlink 'wan'
option zone 'tunnel'
Typical network config for a GREv4 tap tunnel :
config interface 'gretap'
option peeraddr '195.207.5.79'
option mtu '1400'
option proto 'gretap'
option zone 'tunnel'
option tunlink 'wan'
option network 'wlan_ap'
I added myself as maintainer for the moment; feel free to change.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 41897
Make sure they don't break the sed command, and also make device_info
and openwrt_release more robust for parsing by scripts
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41885
Creates /etc/device_info which will be used to fill in information for
WPS and other protocols that need manufacturer/device information
This helps with creating OpenWrt firmware for OEM or rebranded devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41884
This change introduces support for wildcard patterns in "option path"
of section "wifi-device".
Objective is to allow paths like "*/usb[0-9]/*/*" in order to claim
any usb device using the same backend type, regardless of its bus
address or phy name.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41873
This patch brings full dynamic vlan support to netifd that existed in hostapd.sh in Attitude Adjustment.
Signed-off-by: Joseph CG Walker <Joe@ChubbyPenguin.net>
[jow@openwrt.org: changed commit message, rebased on top of current hostapd.sh]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41872
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41858
Since kernel commit 928bea964827 ("PCI: Delay enabling bridges until
they're needed"), pci fixups are run with bridges (e.g. the pcie port)
disabled.
This causses hangs when ath9k_pci_fixup tries to manually enable the
device to apply the register fixups.
Fix this by enabling any parent bridges before trying to access the
device itself.
Fixes boot on DSL-274XB rev F1.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41856
