Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43741
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43740
This will allow us to drop it in the future. This patch doesn't change
the final mtdpart.c, it remains the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43696
This brings ssb and bcma to wireless-testing tag master-2014-12-05
In addition it also adds the ARM-BCM5301X-Add-IRQs-to-Broadcom-s-bus-
axi-in-DTS-f.patch which adds the irq number in a way it is done in the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43544
This is a swconfig driver for the Marvell 88E6171 switch,
which is a 7-port GigE switch with two CPU ports and 64
802.1q VLANs.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43486
Factor out set_mirror_regs to ar8xxx_chip.
Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43468
Factor out info whether switch should be configured at probe stage
to ar8xxx_chip. Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43466
This patch introduces some code that is compiled in whenever
CONFIG_BRIDGE_NETFILTER is built, with the code called from code compiled under
CONFIG_BRIDGE, CONFIG_BRIDGE_IGMP_SNOOPING or CONFIG_BRIDGE_NF_EBTABLES.
Unfortunately, these options aren't setting explicitly the dependency they now
have on CONFIG_BRIDGE_NETFILTER, for obvious reasons for CONFIG_BRIDGE.
However, this is not working really well when CONFIG_BRIDGE_NETFILTER is built
as a module, since code statically compiled will now use a function that is not
in the kernel image, which makes the linker grumpy.
Solve this by removing the option to build CONFIG_BRIDGE_NETFILTER as a module,
and protect our function definition by an IS_BUILTIN instead of a IS_ENABLED
macro. This fixes the issue for CONFIG_BRIDGE and CONFIG_BRIDGE_IGMP_SNOOPING.
Fixing CONFIG_BRIDGE_NF_EBTABLES has to be handled a bit differently, since it
directly references a variable that will not be declared if
CONFIG_BRIDGE_NETFILTER is not set. Protect the variable affectations by an
ifdef to make sure this doesn't happen.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43419
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
