Turn on the auto recovery feature when flashing
and turn it off on successful bootup.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45792
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.
This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45749
Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.
Fixes#19715.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45747
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45729
Patch cherry-picked from the following location:
https://chromium-review.googlesource.com/#/c/269931/
Disable the i2c device on gsbi4 and mark gsbi4_h and gsbi4_qup clks as
unused. If they are enabled, clock framework will turn them off at end
of probe. On ipq806x by design gsbi4_qup, gsbi4_h clks and i2c on gsbi4
are meant for RPM usage. So turning them off in kernel is incorrect.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45728
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)
Signed-off-by: Matteo Panella <m.panella@level28.org>
SVN-Revision: 45725
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45718
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45717
There is also a OHCI controller, activate it for USB 1.1 support.
This should close#19601.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45716
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45709
This patch adds support for the Huawei HG655b.
Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45708
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45705
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).
One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45692
