Update DEPENDS and PROVIDES so that ath10k-ct firmware
and drivers can be used to replace stock firmware
and drivers. The -htt firmware variant, which requires
ath10k-ct driver now selects ath10k-ct driver when the
firmware is selected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.
The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.
Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Updated ppfe firmware to NXP LSDK1712 release. Used
ppfe firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NXP LSDK1712 release used two rcw git trees. The
original rcw git tree was still source code but
dropping ls1012a/ls1088a/ls2088a boards in LSDK1712.
Instead another new rcw git tree was used to just
provided rcw binaries for these boards dropped. So
this patch is to update ls-rcw to LSDK1712 release
and add a new ls-rcw-bin package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
fman-ucode had been migrated from qoriq-open-source
github to NXP github. So the Makefile should be fixed
accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated MC firmware to NXP LSDK1712 release. Used
MC firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* introduces the BDFs for the OpenMesh A42 in
/lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin.
* adds new firmware firmware-6.bin_RM.4.4.1.c1-00037-QCARMSWP-1 for
QCA6174 hw3.0
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Compiling the Intel microcode package results in a
microcode.bin and a microcode-64.bin. As we can
decide based on the subtarget which should be used,
we'll only split the required .bin file with
iucode-tool.
x64 will get the intel-microcode-64.bin
All other variants will get intel-microcode.bin
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the Debian repository for sourcing the ucode files.
Current (20171205) includes support for fam17h CPUs already.
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA988x.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA9887.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9888.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9984.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA4019.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This update automatically includes a new firmware for the QCA6174:
firmware-6.bin_WLAN.RM.4.4.1-00079-QCARMSWPZ-1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
PKG_BUILD_DIR was defined with quoting PKG_VERSION in
layerscape package makefiles. Now PKG_VERSION has been
removed from these makefiles. When PKG_BUILD_DIR quotes
PKG_VERSION, '=' should be used instead ':=' to make
sure PKG_VERSION has been defined in common makefile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.2.1-00058 firmware for the QCA4019.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
layerscape firmware package names collide with existing package contributions.
Ex: layerscape mc and midnight-commander(mc) are in conflict.
Firmware packages: mc, ppa, rcw and dpl are renamed to ls-mc, ls-ppa, ls-rcw
and ls-dpl respectively.
Signed-off-by: Ted Hess <thess@kitschensync.net>
The firmware directory in the Linux kernel was removed in kernel 4.14,
take the e100 firmware files now from the linux-firmware repository
instead. To do so create the new package e100-firmware. This will also
work with older kernel versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
make check complains about PKG_MIRROR_HASH of the wireless-regdb package:
WARNING: PKG_MIRROR_HASH does not match wireless-regdb-2017-10-20-4343d359.tar.xz
hash 5f5b669f32ae36cb65b1d99efbbbfd42c2983cda32f6448346e3e54ffaba3889
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic
This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add data path layout files for the
second generation Data Path Acceleration Architecture.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add package support for Management
Complex Firmware for the second generation Data Path
Acceleration Architecture.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Changes since last LEDE release include:
* Fix key-setting bug that broke sending the EAPOL 2/4 in some cases. This was a
bug I introduced some time back while trying to fix .11r and simplify the key
handling logic. (Patch to wpa_supplicant fixed the race with sending the 4/4
and setting the key...un-patched supplicant will still have this race and the 4-way
auth will not work as reliably.)
* Increase amount of active-tids that can be scheduled. This fixes a tx-stall
seen with many station vdevs.
* Fix bug in upstream code that would cause the maximum peer to never be scheduled
for tx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
