Before starting hostapd we create interface for it. The problem is we
try to create STA interface just to let hostapd change it to AP later.
It may fail if device doesn't support STA interfaces or if we already
hit a limit. Consider following phy (it's from BCM43602 and brcmfmac):
$ iw phy phy0 info | tail
valid interface combinations:
* #{ IBSS, managed } <= 1, #{ AP } <= 4, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
Trying to setup 2 interfaces: STA + AP results in:
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): Configuration file: /var/run/hostapd-phy0.conf
radio0 (1101): Could not read interface wlan0-1 flags: No such device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45856
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.
Fixes#19580
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45855
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45854
Most boards use pci connected usb controllers, so make sure to include
the pci drivers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45840
Some kernel images need to be wrapped in a loader, which cannot be built
without a working toolchain.
Also, this speeds up the image builder run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45836
This is the case e.g. if JFFS2 partition is full.
see: https://www.mail-archive.com/linux-unionfs@vger.kernel.org/msg00246.html
(a small error in a logmessage was changed and reported upstream)
runtime tested on ar71xx with kernel 3.18.11 and r45772
this paritially fixes#19564
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45833
nss-gmac has been replaced by its upstream counterpart "stmmac", to
which we added the SoC glue layer required for it to run on IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45832
This driver has been cherry-picked and backported from the following
LKML thread:
*https://lkml.org/lkml/2015/5/26/744
It also updates the DT accordingly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45831
Most ipq806x platforms use an ethernet switch, and the new upstream
GMAC driver makes use of the Fixed PHY emulation to force the link
settings despite the lack of PHY.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45830
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45828
This include is necessary starting at the PCIe patch, which has a lower
number. So in order to keep the patches consistent, we'll move the
arm-gic include in the first patch who needs it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45827
