Enable dwmac-sun8i Ethernet core to use the built-in FastEthernet port.
Enable exposed UART, USB and I2C pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The lantiq patch 0028-NET-lantiq-various-etop-fixes.patch and sunxi
patch 0051-stmmac-form-4-11.patch no longer applied after applying the
the "generalize napi_complete_done()" patch.
Update them so they apply, and refresh patches while at it.
Fixes: 9aeb7ce8dc ("generic: net: generalize napi_complete_done")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport upstream commit that improves ethernet performance by a
small amount.
Compile and run tested on ipq8065.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
These options are deactivating some kernel modules for IP blocks not
uses on this SoC. I saw the same when working with the ARM64 Marvell
board so it is better to move them to generic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Layerscape uses Cortex-A53 or Cortex-A72 CPU. It's proper
to set below CPU_TYPE for 32-bit mode.
CPU_TYPE:=cortex-a15
CPU_SUBTYPE:=neon-vfpv4
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add linux 4.9 support for layerscape.
All these kernel patches are from NXP LSDK 1709 release.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Rename subtargets 32b/64b with armv8_32b/armv8_64b which are
more proper, and update makefile files. There also will be other
subtargets added in the future, like armv7.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Under heavy load it's possible to overrun the 82574L. When this
happens, Other Interrupt happens and that's erroneously interpreted
as a Link Status Change.
http://patchwork.ozlabs.org/patch/792260/
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.
The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.
Fixes: FS#1043
Signed-off-by: Mathias Kresin <dev@kresin.me>
With kernel commit 7630ea4bda18 ("Documentation: net: phy: improve
explanation when to specify the PHY ID") the purpose of using phy id
specific compatibles was clarified.
Remove the phy id specific compatibles since they are meant to be used
if the phy reports an incorrect or no phy id at all.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The generic nand driver fails to load with:
gen_nand 14000000.nand-parts: platform_nand_data is missing
gen_nand: probe of 14000000.nand-parts failed with error -22
and the xway-nand driver is used afterwards.
Drop the gen_nand compatible to get rid of the error message.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refresh patches.
Compile-tested on brcm2708/bcm2708, octeon and x86/64.
Runtime-tested on brcm2708/bcm2708, octeon and x86/64.
Fixes the following CVEs:
- CVE-2017-1000252
- CVE-2017-12153
- CVE-2017-12154
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Evaluation board 2.2 uses a different status LED pin
The other removed LEDs were never present
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Handle AR9344 as well. Disable the EHCI platform device when device mode
is active, to avoid resource conflicts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This patch adds all the board-specific values currently hardcoded
in mktplinkfw2.c back to the respective device declarations in the
makefiles.
The rationale is to avoid modifying the source code every time a
new board or board variant is added.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Keep Archer C20 Power LED in the same state as it was configured by
bootloader (keep it hightlighed) to avoid unexpectable LED turning off
during kernel boot.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Add the missing USB related kernel config options to target config.
Enable wireless as well, wireless is supported via USB.
Fixes compile/packaging errors with the libertas wireless kernel
module.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not disable SPI in the subtarget, otherwise the SPI driver can not
be used.
Disable SPI by default and enable it in the board specific device tree
source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
AmazonSE and Falcon do not have support for PCI and it can't be
unselected in the subtarget kernel config. This way the enabled PCI
support is inherit from the higher level config to the subtarget.
If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and
all packages depending on this config symbol will be build and at least
some of them fail due to missing pci functions.
The issue can be observed if all kmods and all non-shared packages are
build. Fix the issue by enabling PCI support only in subtargets with
PCI support.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or
global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_SPI_LANTIQ was replaced by CONFIG_SPI_LANTIQ_SSC with the switch
to the upstreamed driver.
All other removed subtarget kernel config options are already set by
the target specific or global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel.
CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch
to the upstreamed driver.
Add autoselected dependecies to the kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_GPIO_DEVRES was removed with kernel commit f9c22ec6c1c5 ("gpio:
Remove GPIO_DEVRES option") during kernel 4.9 development.
CONFIG_HAVE_BPF_JIT was removed with kernel commit 6077776b5908 ("bpf:
split HAVE_BPF_JIT into cBPF and eBPF variant") during kernel 4.7
development.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following features are working and tested:
* both Ethernet ports
* MMC
* LED
The following features are not working:
* Wifi (There is a crappy driver we could port)
* SPI flash (I haven't looked into this)
I haven't tried out the rest.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
check if the config option CONFIG_LANTIQ is defined.
This fixes the following warning:
CC [M] drivers/misc/owl-loader.o
drivers/misc/owl-loader.c: In function 'ath9k_pci_fixup':
drivers/misc/owl-loader.c:92:5: warning: "CONFIG_LANTIQ" is not defined [-Wundef]
#if CONFIG_LANTIQ
^
Fixes: e9401a2335 ("kernel: owl-loader for delayed Atheros ath9k fixup")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner H3 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner A64 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the GMAC which is use in the A64 and other
Allwinner chips by backporting the changes from the kernel versions
4.13.
Some commits are not backported which are adding support for newly
introduced APIs which are not available in kernel 4.9.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The RT5350F's second UART pins are available on the base module and on
the EVB as well, so enable it in the device tree.
In order to keep the origian serial port numbering (ttyS0 is the serial
console), aliases added for the UART devices.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F i2c pins is available on the base module and on
the EVB as well, so enable it in the dts.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
