Commit graph

71 commits

Author SHA1 Message Date
INAGAKI Hiroshi
4645a6d318 ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:01 +02:00
Christian Mehlis
0c7e78930b ipq806x: add support for Compex WPQ864
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
           256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer

The correct amount of RAM will be passed by the bootloader.

In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.

So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.

OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.

It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.

In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:

  (IPQ) # set bootargs " "
  (IPQ) # set fsbootargs " "
  (IPQ) # saveenv

The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):

  (IPQ) # set serverip 192.168.1.20
  (IPQ) # set ipaddr 192.168.1.1

  (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
  (IPQ) # crc32 0x42000000 $filesize

  (IPQ) # nand erase 0x1340000 0x4000000
  (IPQ) # nand write 0x42000000 0x1340000 $filesize

The initramfs image can be started using:

  (IPQ) # set fdt_high 0x48000000
  (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
  (IPQ) # bootm 0x44000000

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-15 08:17:10 +01:00
John Crispin
b7f115f22a ipq806x: drop ipq40xx support
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Dongming Han
04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
Stefan Lippers-Hollmann
4baffa02ce ipq806x: switch to full dual-boot for the nbg6817 sysupgrade support
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.

The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Stefan Lippers-Hollmann
42fe7b3bbe ipq806x: request the first free loop device dynamically for the nbg6817 sysupgrade
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Stefan Lippers-Hollmann
b36cf0be30 ipq806x: use absolute the device path in $kernel for the nbg6817 sysupgrade
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
David Bauer
1113fcdc80 ipq806x: mark AVM FB4040 switchport as untagged
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-02-11 16:02:52 +01:00
Mathias Kresin
b6868e2f47 ipq806x: fix ZyXEL NBG6817 sysupgrade
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.

It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.

Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:22:37 +01:00
Sven Eckelmann
86e18f6706 ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00
Luis Araneda
7293499f71 ipq806x: Sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
33f09cf151 ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree

Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script

Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
09e13bd341 ipq806x: add a helper variable with the vendor name stripped
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.

None of the current boards use a comma in the boardname, so they
will be unaffected.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:02 +01:00
Christian Lamparter
da6fdce365 base-files: unify get_dt_led helper function
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.

This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.

Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2017-12-14 09:29:30 +01:00
Stefan Lippers-Hollmann
9a221c6d69 ip806x: nbg6817: sysupgrade support both targets for kernel/ rootfs partitions
With this commit and the previous "nbg6817: don't hardcode the rootfs location
by using append-rootblock instead" applied, it is possible to boot- and
sysupgrade from both dual-boot sets (the primary mmcblk0p4+mmcblk0p5 or the
alternative mmcblk0p7+mmcblk0p8). However the sysupgrade support does not
toggle between both dual-boot sets between firmware upgrades so far.

The partition map of the eMMC used in the nbg6817 is:

Found valid GPT with protective MBR; using GPT.
Disk /dev/mmcblk0: 7471104 sectors, 3.6 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): XXX
Partition table holds up to 12 entries
First usable sector is 34, last usable sector is 7471070
Partitions will be aligned on 2-sector boundaries
Total free space is 1 sectors (512 bytes)

Number  Start (sector)    End (sector)  Size       Code  Name
   1              34            8225   4.0 MiB     FFFF  rootfs_data
   2            8226           16417   4.0 MiB     FFFF  romd
   3           16418           18465   1024.0 KiB  FFFF  header
   4           18466           26657   4.0 MiB     FFFF  kernel
   5           26658          157729   64.0 MiB    FFFF  rootfs
   6          157730          159777   1024.0 KiB  FFFF  header_1
   7          159778          167969   4.0 MiB     FFFF  kernel_1
   8          167970          299041   64.0 MiB    FFFF  rootfs_1
   9          299042          823329   256.0 MiB   FFFF  bu1
  10          823330         7471069   3.2 GiB     FFFF  bu2

rootfs_data is the ext4 formatted overlay of the OEM firmware, LEDE
ignores it due to its (too) small size.

romd/ bu1 are initialized with zeroes (0x00) and unused.

bu2 is formatted with ext4 and used for streamboost and other optional
functionality by the OEM firmware, it is reformatted during factory
resets of the OEM firmware.

header/ header_1 contains version information for the corresponding
vendor firmwares installed to kernel/rootfs or kernel_1/ rootfs_1, the
format hasn't been completely reverse engineered so far and remains
left untouched by LEDE:

V1.00(ABCS.2)C0:
 00000000  00 00 a7 74 01 32 f0 00  56 31 2e 30 30 28 41 42  |...t.2..V1.00(AB|
 00000010  43 53 2e 32 29 43 30 00  ff ff ff ff ff ff ff ff  |CS.2)C0.........|
 00000020  ff ff ff ff ff ff ff ff  00 00 d5 dc 4e 42 47 36  |............NBG6|
 00000030  38 31 37 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |817.............|
 00000040  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000060  ff ff ff ff ff ff ff ff  ff ff ff ff 00 00 22 a3  |..............".|
 00000070  00 1c 70 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |..p.............|
 00000080  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000800  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
 *
 00100000

V1.00(ABCS.5)C0:
 00000000  00 00 bf 94 01 46 d8 00  56 31 2e 30 30 28 41 42  |.....F..V1.00(AB|
 00000010  43 53 2e 35 29 43 30 00  ff ff ff ff ff ff ff ff  |CS.5)C0.........|
 00000020  ff ff ff ff ff ff ff ff  00 00 d6 5a 4e 42 47 36  |...........ZNBG6|
 00000030  38 31 37 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |817.............|
 00000040  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000060  ff ff ff ff ff ff ff ff  ff ff ff ff 00 00 c0 2c  |...............,|
 00000070  00 1c 58 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |..X.............|
 00000080  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00010000  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
 *
 00100000

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-10-29 03:11:51 +01:00
Roman Yeryomin
156f2df879 ipq806x: ipq4019: add ap-dk01.1-c1 board support
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)

First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize

Further upgrades via sysupgrade.

Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition

Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.

Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.

Changes since v2:
- based on dts(i) rework/cleanup submitted:
  http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:24:26 +02:00
Stefan Lippers-Hollmann
189433e543 ipq806x: nbg6817: sync MAC addresses to the upstream values
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.

interface	  new/ OEM MAC	old MAC

wlan-2.4g (phy1): ethaddr	undefined
wlan-5g   (phy0): ethaddr + 1	undefined
lan             : ethaddr + 2	ethaddr
wan             : ethaddr + 3	ethaddr + 1

This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-11-03 20:04:51 +01:00
Baptiste Jonglez
5889f92f7d ipq806x: Archer C2600: fix switch ports numbering
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device.  Fix the order so that they match.

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-08-24 08:39:12 +02:00
Mathias Kresin
e4e984f2a0 treewide: use only board_name function to get name
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.

The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
e0b9ec8e96 treewide: drop target board_name functions
They are not used any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
ac3e05c5d7 treewide: populate boardname and model earlier
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.

Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Matthias Schiffer
438dcbfe74
base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.

The list of binaries is also slightly cleaned up and duplicates are
removed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:26:32 +02:00
Matthias Schiffer
08a94ecaee
ipq806x: upgrade: fix RAMFS_COPY_*
RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded
linksys_preupgrade function is removed, and the nand_do_upgrade call is
moved to platform_do_upgrade.

Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Pavel Kubelun
189239ade3 ipq806x: qca99xx: fix wifi calibration
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.

Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).

Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-06-17 11:51:41 +02:00
Ram Chandra Jangir
e178d51a04 ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.

Testing:
 *Tested on IPQ40xx AP-DK04.1-C1:
   a. NAND boot
   b. ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Mathias Kresin
822ee54544 treewide: fix device tree path in scripts
The device tree is at /proc/device-tree/ without a base subdir.

Fixes: da472e5b30 ("treewide: access device tree from userspace via /proc/")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 15:18:30 +02:00
Mathias Kresin
da472e5b30 treewide: access device tree from userspace via /proc/
Access the device tree via /proc/device-tree/ is the documented way to
access the properties. Everything else might not work in future.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Jo-Philipp Wich
3c3f7cfe4d ipq806x: fix EA8500 switch configuration
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.

Ref: https://github.com/openwrt/luci/issues/1086

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-03 14:15:34 +02:00
Christian Lamparter
1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Jo-Philipp Wich
ea269c37b8 ar71xx/ipq806x/mediatek/mvebu: fix network defaults
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.

Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-07 09:32:28 +01:00
Hannu Nyman
c980147527 ipq806x: fix wireless macs
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.

Fixes: FS#451

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 19:31:45 +01:00
Zhang Jingye
71a39b8690 ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.

This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.

Signed-off-by: Zhang Jingye <934526987@qq.com>
2017-01-18 12:05:18 +01:00
Adrian Panella
d700c120bf ipq806x: EA8500 fix sysupgrade over stock firmware
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-12-20 09:35:37 +01:00
Mathias Kresin
3228c2a682 ipq806x: more dts cleanup
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.

Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.

Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.

If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.

Use the usb pinmux settings from the nbg6817 gpl sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:33:54 +01:00
Henryk Heisig
e3caadc69d ipq806x: clean up dts files
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).

This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.

Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.

Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.

Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.

Change gpioexport to gpio pinmux.

Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.

Remove pcie pinmux from D7800.

Move pinctrl to correct place in NBG6817 and R7800.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-27 15:24:59 +01:00
Sebastian Quilitz
ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Henryk Heisig
c380772c19 ipq806x: c2600: change wan and lan led trigger to swconfig port
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-21 10:04:55 +01:00
Felix Fietkau
b5ee86c4e5 ipq806x: remove device specific sysupgrade image checks
Replaced by image metadata

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-20 20:08:39 +01:00
Felix Fietkau
9d6d7d9a0e ipq806x: append metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Pavel Kubelun
5aace5a5fb ipq806x: fixes for R7800 and C2600
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
bf7166e545 ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Cezary Jackiewicz
dafbc94f95 ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbport
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-11-03 08:21:32 +01:00
André Valentin
1465bebd74 ipq806x/nbg6817: add sysupgrade support
Add new way of flashing to mmc devices based on rootfs split with loop devices.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin
a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Henryk Heisig
bcfb535730 ipq806x: C2600: change leds colour name
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Henryk Heisig
4bdf615878 ipq806x: add support for indicating the boot and upgrade state using four leds
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Pavel Kubelun
9677bfbb0f ipq806x: fix wlan mac for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-06 08:01:33 +02:00
Cezary Jackiewicz
9417293366 ipq806x: Archer C2600: Renaming LED accordance with the standard
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
2016-08-24 00:21:34 +02:00
Alexis Green
c34f953fef ipq806x: Build image for Netgear Nighthawk X4 R7500v2
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-08-22 17:24:48 +02:00