Commit graph

578 commits

Author SHA1 Message Date
Christian Lamparter
d82d84694e apm821xx: add support for the Netgear WNDAP620 and WNDAP660
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.

Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM:  128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes

Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM:  256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes

Flashing requirements:

 - needs a tftp server at 192.168.1.10/serverip.
 - special 8P8C(aka RJ45)<->D-SUB9 Console Cable
   ("Cisco Console Cable"). Note: Both WNDAP6x0 have
   a MAX3232 transceivers, hence no need for any separate
   CMOS/TTL level shifters.

External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
 = Config# = | = GPIO 11 = | = GPIO 14 = |  ===== Description =====
      1.     |   1 / High  |  0 / Low    | Use the internal antennae (default)
      2.     |   0 / Low   |  1 / High   | Use the external antennae

The external antennaes are only meant for the 2.4 GHz band.

One-way Flashing instructions via u-boot:

 0. connect the serial cable to the RJ45 Console Port
    Note: This requires a poper RS232 and not a TTL/USB adaptor.

 1. power up the AP and interrupt the u-boot process at

    'Hit any key to stop autoboot'

 2. setup serverip and ipaddr env settings
    Enter the following commands into the u-boot shell
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.10

 3. download the factory.img image to the AP
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img

 4. verfiy image integrity
    Enter the following commands into the u-boot shell

    # crc32 $fileaddr $filesize

    If the calculated crc32 checksum does not match, go back to step 3.

 5. flash the image
    Enter the following commands into the u-boot shell

    # nand erase 0x110000 0x1bd0000
    # nand write ${kernel_addr_r} 0x110000 ${filesize}

 6. setup uboot environment
    Enter the following commands into the u-boot shell

    # setenv bootargs
    # setenv fileaddr
    # setenv filesize
    # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
    # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
    # setenv bootcmd 'run owrt_boot'
    # saveenv

 7. boot
    # run bootcmd

Booting initramfs instructions via u-boot:

 Follow steps 0 - 2 from above.

 3. boot initramfs
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
    # run addtty
    # bootm ${kernel_addr_r}

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
e21a9db47d apm821xx: MX60(W): enable u-boot environment
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved  environment"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
f6968952df apm821xx: MR24: add to uboot-envtools
This patch adds the complicated u-boot
environment access settings for to the
MR24 target.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
6f4f77aa1d apm821xx: add uboot-envtools support
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Michael Heimpold
79b766d07d uboot-mxs: bump to v2018.09
Also update the U-Boot BSP patch for I2SE Duckbill devices
and remove upstreamed patch for LibreSSL support.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-11-01 17:16:52 +01:00
Philip Prindeville
a6d02a7572 grub2: fix regression caused by binutils-2.31.1
grub-efi no longer works:

grub-mkimage: error: relocation 0x4 is not implemented yet.

See:

http://git.savannah.gnu.org/cgit/grub.git/commit/util?id=842c390469e2c2e10b5aa36700324cd3bde25875

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>i [PKG_RELEASE increase]
2018-10-25 16:51:42 +02:00
Julian Haupt
0308385d1d sunxi: add support for Orange Pi Zero
Signed-off-by: Julian Haupt <julian.haupt@hauptmedia.de>
2018-10-07 22:16:10 +02:00
Thomas Nixon
6b729e1563 uboot-lantiq: fix compile with modern host dtc
In dtc version 1.4.6 the macro names in header include guards changed,
but the build relies on them matching in order to replace selected
headers. This is a horrible hack to work around this.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2018-10-07 02:12:06 +02:00
Ansuel Smith
43e71e0416 uboot-envtools: adds r7800 uboot env support
This fix and adds support for r7800 uboot env

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2018-10-07 02:12:06 +02:00
Martin Schiller
e86cdf85a7 uboot-lantiq: fix compatibility with gcc7
Backport u-boot commit 704f3acfcf55343043bbed01c5fb0a0094a68e8a to fix
compatibility with gcc7.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-09-26 20:35:07 +02:00
Yangbo Lu
7016dd48f1 layerscape: add ls1012afrwy support and drop ls1012afrdm
ls1012afrdm was no longer supported in NXP Layerscape SDK.
Instead a new board ls1012afrwy was introduced in LSDK.
This patch is to drop ls1012afrdm and add ls1012afrwy support.
Since only 2MB NOR flash could be used, we just put u-boot
and firmware on NOR flash, and put kernel/dtb/rootfs on SD
card.

The Layerscape FRWY-LS1012A board is an ultra-low-cost
development platform for LS1012A Series Communication
Processors built on Arm Cortex-A53. This tool refines the
FRDM-LS1012A with more features for a better hands-on experience
for IoT, edge computing, and various advanced embedded
applications. Features include easy access to processor I/O,
low-power operation, micro SD card storage, an M2 connector, a
small form factor, and expansion board options via mikroBUS Click
Module. The MicroBUS Module provides easy expansion via hundreds
of powerful modules supporting sensors, actuators, memories,
and displays.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:57 +02:00
Yangbo Lu
eb684205e5 layerscape: add SD card boot support
NOR/QSPI Flash on Layerscape board only has limited 64MB memory size.
Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr)
could support SD card boot, we added SD boot support for them to put
all things on SD card to meet large memory requirement.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:57 +02:00
Yangbo Lu
f0ec7bd27d layerscape: add armv7 subtarget and ls1021atwr board support
The NXP TWR-LS1021A module is a development system based
on the QorIQ LS1021A processor.
- This feature-rich, high-performance processor module can
  be used standalone or as part of an assembled Tower System
  development platform.
- Incorporating dual Arm Cortex-A7 cores running up to 1 GHz,
  the TWR-LS1021A delivers an outstanding level of performance.
- The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as
  well as a complete Linux software developer's package.
- The module provides a comprehensive level of security that
  includes support for secure boot, Trust Architecture and
  tamper detection in both standby and active power modes,
  safeguarding the device from manufacture to deployment.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:57 +02:00
Yangbo Lu
ad1dbc0ca3 layerscape: add u-boot environment support for OpenWrt boot
This patch is to implement u-boot environment txt files
to support OpenWrt boot for all layerscape devices.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00
Yangbo Lu
dcf57c766a layerscape: update u-boot to LSDK-18.06
The u-boot source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. This
patch is to update u-boot to LSDK-18.06 for both
uboot-layerscape and uboot-layerscape-armv8_32b packages.
Besides, this patch also introduced some other changes.
- Reworked uboot-layerscape makefile to make it more
  readable.
- Define package in uboot-layerscape-armv8_32b for each board.
- Fixed u-boot package selection in target image makefile.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00
Yangbo Lu
e83faa3d7d layerscape: drop uboot-layerscape patches
Dropped uboot-layerscape patches which were environemnt patches.
We will make u-boot environment binaries with a txt file for all
devices.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-09-22 21:20:56 +02:00
Jasper Scholte
a689307c97 sunxi: build image/uboot for the NanoPi NEO2
The NanoPi NEO2 is a small Allwinner H5 based board available with
different DRAM configurations.
This board is very similar to the NanoPi NEO PLUS2

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
2018-09-22 21:20:55 +02:00
Luis Araneda
e2a4d14aaa uboot-zynq: use a file to modify the default environment
Follow the strategy of other targets and create a
default environment file, uEnv.txt, to configure the
behavior of U-Boot.
For now, use it to pass bootargs to the kernel

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:54:41 +02:00
Luis Araneda
306a60fcfe uboot-zynq: copy U-Boot images to STAGING_DIR
Create a directory inside STAGING_DIR and copy U-Boot
output images, so they can be used later when creating the
sdcard image

Additionally, like others targets, override the default
install method to avoid copying the images to bin directory

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:54:25 +02:00
Luis Araneda
e62df3dd8b uboot-zynq: automatically select the appropriate variant
Select the U-Boot variant automatically based on the
current selected device, and hide the package from
menuconfig

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:54:00 +02:00
Luis Araneda
5d2b702590 uboot-zynq: remove ZC706 board
The board was added when creating the target, but the
corresponding device was never defined inside the target

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:53:28 +02:00
Felix Fietkau
36c6ba3735 imx6: use BUILD_DEVICES in uboot-imx6 for mx6cuboxi
Fixes build with the default profile

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-05 10:00:01 +02:00
Felix Fietkau
7165378d19 uboot-imx6: fall back to MMC for SPL if boot mode is invalid
Fixes boot on Hummingboard

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Felix Fietkau
aa3efca8d9 uboot-imx6: remove obsolete patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Felix Fietkau
eab7bcc8e1 uboot-imx6: install images into STAGING_DIR_IMAGE
Will be used by a new combined image for cubox

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Vladimir Vid
6cda4f6861 imx6: Initial support for SolidRun CuBox-i devices based on i.MX6 processors (i1, i2, i2eX, and i4Pro).
- Specifications -

CuBox i1:
- SoC: i.MX6 Solo
- Cores: 1
- Memory Size: 512MB
- GPU: GC880
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps

CuBox i2 | i2eX:
- SoC: i.MX6 Dual Lite
- Cores: 2
- Memory Size: 1GB
- GPU: GC2000
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps

CuBox i4Pro | i4x4:
- SoC: i.MX6 Quad
- Cores: 4
- Memory Size: 2/4 GB
- GPU: GC2000
- Wifi/Bluetooth: Build In
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps

Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded.
SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory.

Flashing the SPL:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4
dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1

Preparing the firmware on the SD-card:
(echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0
mkfs.ext4 /dev/mmcblk0p1
mount /dev/mmcblk0p1 /mnt
tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/
mkdir -p /mnt/boot
cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/

Generated u-boot.img needs to be placed on the first partition:
cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/

To boot from the SD card:

Boot script which sets mmc/dtb parameters and boots the board is automatically sourced.
If this does not work for any reason:
mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr

Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available.

Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working.
Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2018-08-25 15:40:23 +02:00
Luis Araneda
43dedd0661 uboot-zynq: add support for the zybo z7 board
Backport board support from the upcoming v2018.09 release,
and add an additional patch to read the MAC address
from flash memory

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-08-25 15:33:50 +02:00
Jo-Philipp Wich
9ffbe84ea4 grub2: rebase patches
Patch 300-CVE-2015-8370.patch was added without proper rebasing on the
version used by OpenWrt, make it apply and refresh the patch to fix
compilation.

Fixes: 7e73e9128f ("grub2: Fix CVE-2015-8370")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-23 19:08:58 +02:00
Rosen Penev
7e73e9128f grub2: Fix CVE-2015-8370
This CVE is a culmination of multiple integer overflow issues that cause
multiple issues like Denial of Service and authentication bypass.

More info: https://nvd.nist.gov/vuln/detail/CVE-2015-8370

Taken from Fedora.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-08-23 07:15:53 +02:00
Rosen Penev
7961009346 yamonenv: Remove dead URLs
uscan errors on the URL as it is no longer available.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-08-22 11:22:17 +02:00
Rosen Penev
f5098a69ed fconfig: Remove dead URLs
uscan errors on the URL as it is no longer available.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-08-22 11:22:04 +02:00
Rosen Penev
f2e1fd0f35 apex: Remove dead URL.
uscan errors on the URL as it is no longer available.

Also switched the download URL to HTTPS.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-08-22 11:21:53 +02:00
Luis Araneda
09ac4aa86b uboot-zynq: update to 2018.07
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-08-13 08:43:58 +02:00
David Bauer
c4931713df ath79: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-09 18:44:57 +02:00
Antonio Silverio
e2e39328d5 sunxi: Added support for Xunlong Orange Pi PC2
CPU: H5 High Performance Quad-core 64-bit Cortex-A53
GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL
Memory: 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB)
Onboard Network: 1000M/100M Ethernet RJ45
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode
role by default in DTS
Buttons: Power Button(SW4) Debug TTL

UART: ..DC-IN..
>[GND][RX][TX] ..HDMI..

Signed-off-by: Antonio Silverio <menion@gmail.com>
2018-08-09 12:06:58 +02:00
David Bauer
5107ba2374 uboot-envtools: add ath79 target
This adds uci entries for all ath79 devices for which this already was
the case on ar71xx. Additionally we add the OCEDO Koala as there was no
support in OpenWRT yet.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 08:38:45 +02:00
Ademar Arvati Filho
27b2f0fc0f kirkwood: add support for Iomega Storcenter ix2-200
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00
Lucian Cristian
40f66f1431 omap: rename image for sysupgrade compatibility
for sysupgrade to work we need to change the image name based on dts target name

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Mathew McBride
ae95a8ad3e uboot-envtools: add configuration for Traverse LS1043 boards.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Edi Turn
e9dee19487 grub2: fix packed-not-aligned error on GCC 8
Fix the compile error "packed-not-aligned" when using GCC 8.

Signed-off-by: Edi Turn <yyxstter@gmail.com>
2018-07-30 10:42:47 +02:00
Vladimir Vid
856cc6d999 uboot-imx: bump to 2018.03 which fixes the build issues with fdt64_t redefinitions
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2018-07-07 18:33:57 +02:00
Alberto Bursi
e13d9cd07f uboot-kirkwood: fix malformed boot configuration
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----

If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----

The "bootargs_root=" that was appended to it should not be there.

Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.

This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.

Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-06-27 08:42:54 +02:00
Alberto Bursi
ccd1dc3d20 uboot-kirkwood: fix whitespaces
remove whitespaces from the patches

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-06-27 08:42:54 +02:00
Christian Lamparter
82618062cf ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617

Hardware highlights:

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR:    32 MiB Macronix MX25L25635F
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS:   Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS

Serial:
	WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
	The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
	pre-soldered. Pinout:
	  1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX

first install / debricking / restore stock:
 0. Have a PC running a tftp-server @ 192.168.1.99/24
 1. connect the PC to any LAN-Ports
 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
    into the tftp-server root directory and rename it to just "ras.bin".
 3. power-cycle the router and hold down the the WPS button (for 30sek)
 4. Wait (for a long time - the serial console provides some progress
    reports. The u-boot says it best: "Please be patient".
 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
    flashes fast at the same time. You have to reboot the device and
    it should then come right up.

Installation via Web-UI:
 0. Connect a PC to the powered-on router. It will assign your PC a
    IP-address via DHCP
 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
 2. Go to the "Expert Mode"
 3. Under "Maintenance", select "Firmware-Upgrade"
 4. Upload the OpenWRT factory image
 5. Wait for the Device to finish.
    It will reboot into OpenWRT without any additional actions needed.

To open the ZyXEL NBG6617:
 0. remove the four rubber feet glued on the backside
 1. remove the four philips screws and pry open the top cover
    (by applying force between the plastic top housing from the
    backside/lan-port side)

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6617> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6617>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6617> ATSE NBG6617
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6617> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6617> ATGU
|NBG6617#

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-26 08:57:26 +02:00
Daniel Golle
ff0f3522b7 uboot-oxnas: fix typo accidentally committed during oxnas reboot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-18 18:55:19 +02:00
Hauke Mehrtens
9a26a9e8b9 uboot-sunxi: update Orange Pi R1 and Zero Plus
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:20 +02:00
Hauke Mehrtens
f2135e7811 uboot-sunxi: update to version 2018.05
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.

This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:20 +02:00
Hauke Mehrtens
7afe1caf70 arm-trusted-firmware-sunxi: update to version from 2018-02-10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:20 +02:00
David Bauer
e36f8b3f39 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-07 09:31:58 +02:00
Luis Araneda
8c8499f0ea uboot-zynq: update to 2017.03
Compile-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00