This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42088
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42083
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41835
Some devices were renamed when converted from diag to in kernel board detection and it was not changed in netconfig. Devices not in the
kernel board detection are removed now.
This should close: #17111, #16968, #13202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41663
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41548
broadcom-wl now builds in the mips74k profile, so remove these chips
from the generic profile.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41546
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41527
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41515
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41513
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41512
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.
Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41500
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
With this patch the mips74k subtarget will be compiled with optimized
compiler options to generated smaller and faster code. This currently
breaks broadcom-wl, because the binary blob is only compiled with
mipsr1 support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41050
This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.
This was reported and tested by ernesto (Faulp3lz).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41042
All new devices (with MIPS 74K CPU) are based on BCMA SoC and have
Ethernet core supported by bgmac. Create a new subtarget to generate
optimized builds.
This is just a beginning, further tweaks (like kernel configuration)
are still possible. This decreases default root.squashfs by ~128 kB.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41025
This allows creating more subtargets and optimize builds per family.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41024
