The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.
Not tested:
* SD card reader.
Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
In case the link changes from down to up, the register is only updated
on read. If the link failed/was down, this bit will be 0 until after
reading this bit again.
Fixes a reported link down by swconfig alebit the link is up (query for
the link again will show the correct link status)
Signed-off-by: Mathias Kresin <dev@kresin.me>
In conditions where none of the switch ports is connected during boot,
the priv->port[i].link != priv->port[i].phydev->link condition is false
since both link values are equal (false). The carrier of the switch
netdev is never set to off and the link state reported by ip is UNKNOWN.
Turn the carrier off if none of the switch ports has a link, regardless
whether something has been changed. Add a check for a carrier to
prevent unnecessary calls to netif_carrier_off() if the carrier is
already off.
Based on a patch send by Martin Schiller.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 77645ffcd9 ("ramips: add support for the GnuBee Personal Cloud
One") dropped the execution permission from 01_leds with the result
that the file isn't started during first boot and no default LED
configuration is added.
Revert the introduced file permission change.
Fixes: FS#979
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[cherry picked the fix from a board support patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WAN port on the Netgear WNDR4300 router has two LEDs,
amber and green. Use the switch LED trigger to behave as the
rest of the LAN HW controlled LEDs
- Green: 1 Gbps
- Amber: 100/10 Mbps
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
mode when connected to 10M/100M ethernet.
Signed-off-by: Kuang Rufan <master@a1983.com.cn>
Refresh patches.
Compile-tested on ramips/mt7621 and x86/64.
Runtime-tested on ramips/mt7621 and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This generic structure defines tx_bytes and rx_bytes as unsigned long (u32),
while several devices would typically report unsigned long long (u64).
The code can work as is, but there's a chance that with a sufficiently fast
interface the overflow might happen too fast to be correctly noticed by the
consumers of this data.
This patch makes both field unsigned long long and updates the only known
consumer of this data: swconfig_leds.c
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
The implementation uses a generic callback that select the correct MIB counter
index based on chip version.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"
They are essentially a single subtarget.
This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* fixes default affinity
* adds a napi watchdog - we were seeing stalled TX queues
* adds up/down locking
Signed-off-by: John Crispin <john@phrozen.org>
Install kmod-rt2800-pci instead of only the rt2x00 library.
Fixes missing wireless interface on AudioCodes AC-MP252.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Neon and vfpv4 support are activated by GCC on all ARMv8 CPUs because
this is now a mandatory part of the architecture. There is not need to
activate is manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Comtrend AR-5315u router
This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This commit adds support for Xiaomi Mi WiFi Router 3G.
Short specification:
- MT7621AT + MT7603EN + 7612EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+2 x 1000M Ethernet
- 1x USB 3.0 port
- reset button
- yellow, blue, red leds
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot
Originally stock firmware has following partitions:
- ...
- kernel0 (primary kernel image)
- kernel1 (secondary kernel image, used by u-boot in failsafe routine)
- rootfs0 (primary rootfs)
- rootfs1 (secondary rootfs in case primary fails)
- overlay (used as ubi overlay)
This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.
This device lacks hw watchdog, so adding softdog instead (stock does the same).
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The Gateworks System Controller (GSC) mimics a standard AD7418 device on
I2C bus 0 at slave 0x29.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.
Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.
Removed memory node in the device tree source file.
Memory is detected automatically.
http://vocore.io/http://vonger.net/http://vonger.cn/
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector
Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.
Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.
Fixes: FS#670
Signed-off-by: Mathias Kresin <dev@kresin.me>
USB doesn't work in some danube boards because otg_cap
is missing since previous changes made on the USB-dwc2
lantiq driver. Fix it.
Tested on the ARV7518PW router.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.
This patch fixes the MAC address for wlan2g in line with OFW.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes it possible to simply add additional notification handlers
by putting new scripts in the /etc/hotplug.d/dsl directory.
the following Environment Variables are used:
(values marked with an * are only available when bonding support is
compiled in)
DSL_NOTIFICATION_TYPE with one of these values:
- DSL_STATUS
- DSL_INTERFACE_STATUS
- DSL_DATARATE_STATUS_US
- DSL_DATARATE_STATUS_DS
DSL_LINE_NUMBER=<0|1> *
If DSL_NOTIFICATION_TYPE == DSL_STATUS, these variables are set:
- DSL_XTU_STATUS=<ADSL|VDSL>
- DSL_TC_LAYER_STATUS=<ATM|EFM>
- DSL_EFM_TC_CONFIG_US=<NORMAL|PRE_EMPTION>
- DSL_EFM_TC_CONFIG_DS=<NORMAL>
If DSL_NOTIFICATION_TYPE == DSL_INTERFACE_STATUS, these variables are
set:
- DSL_INTERFACE_STATUS=<DOWN|READY|HANDSHAKE|TRAINING|UP>
- DSL_BONDING_STATUS=<INACTIVE|ACTIVE> *
If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_US, these variables are
set:
- DSL_DATARATE_US_BC0=<Upstream data rate in bit/s for Channel 0>
- DSL_DATARATE_US_BC1=<Upstream data rate in bit/s for Channel 1> *
If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_DS, these variables are
set:
- DSL_DATARATE_DS_BC0=<Downstream data rate in bit/s for Channel 0>
- DSL_DATARATE_DS_BC1=<Downstream data rate in bit/s for Channel 1> *
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fix when add 'mediatek,cd-poll' to dts cause the sd card be removed randomly.
Special for the device without card-detect pin.
Signed-off-by: Qin Wie <me@vonger.cn>
Use the GPIO dt-bindings macros and add compatible strings in the
ramips device tree source files.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Netgear EX3800 is essentially an EX3700 with a mains output socket.
Both devices use the exact same firmware image (original firmware is named
EX3700-EX3800-version.chk).
This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and
updating the necessary glue.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch cleans up the WN3000RPv3 and EX2700 setup, bringing it in line
with other similar devices:
The power led is a bicolor one. The bootloader brings the red side on at
powerup.
Instead of blinking the red side in diag.sh and need to forcefully turn it off
in 01_leds, this patch simplifies the setup by relying on the default off state
of the gpio-led driver for the red side and blinking the green side as with
other devices.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Cleanup the dtsi files and remove one layer of dtsi. Set the size of
the firmware partition to a value matching the flash size from the
board (variant) name.
Remove the usb led trigger. There is neither a default config for the
usb led trigger nor a LED for usb activity indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
So, this is kind of complicated. This has been upstream for a while,
imported from OpenWRT/LEDE with some cleanups. LEDE ramips has stayed
on linux-4.4 this whole time, with the old(er) version of the patch
that had correct behavior[0], while upstream got changed[1].
When LEDE updated to kernel 4.9, the older version of the code from
the patch got replaced with the upstream version containing the bug.
The original behavior, however, seems to be correct here, as the
official programming guide[2] indicates that bit 31 (PDRV_SW_SET)
in register PPLL_CFG1 is reserved, but bit 23 (added as PPLL_LD)
is the PPLL lock state (which also happens to line up with the
error message).
The original confusion probably comes from the double definition
of PDRV_SW_SET[3, 4] in the upstream code, with one correct definition
(31) and one incorrect one (23).
I've also used the opportunity to clean up the error message a bit -
it's still not really helpful to anyone who doesn't already know what
the PPLL is, but at least it's slightly more readable now.
This will probably need to be upstreamed as well, since with the way
it's currently set up, it's unlikely PCI ever worked for anyone who's
running an upstream kernel on that SoC.
[0]: 05d6e92594/target/linux/ramips/patches-4.4/0009-PCI-MIPS-adds-mt7620a-pcie-driver.patch (L259)
[1]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L246)
[2]: http://www.anz.ru/files/mediatek/MT7620_ProgrammingGuide.pdf
[3]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L36)
[4]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L39)
Signed-off-by: Ilya Katsnelson <me@0upti.me>
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in wrong order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
All LEDs GPIOs are active low on this device.
WAN and POWER states were inverted. Add default state for power.
Tested on Archer C50v1.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
With d2b6bf1416 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.
Revert this change and use the former board name in the metadata
instead.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix incorrect offset and size of linux partition.
Fixes: 97b36aca09 ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.
Specifications:
- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
The square hole is pin 1
The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.
Flash instructions:
You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.
Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.
Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").
Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Children of the pinctrl0 node are optional. Return EINVAL (=missing)
instead of 0. Fixes a hang if the pinctrl0 has no children.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
there were 2 bugs
*) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize
*) HPT frequency was not set making r4k timers not come up properly
Signed-off-by: John Crispin <john@phrozen.org>
The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 2.5" Drives
- One micro SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: 1 x WAN and 1 x LAN
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Four GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud One ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in inverted order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The VoCore2 features 128MB of RAM, therefore set
memory in DTS to 128*1024*1024 = 0x8000000
The board's LED is connected to GND, set it to
ACTIVE_HIGH here.
Make serial console working again on kernel 4.9 by
change of pinmux configuration.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.
Firmware wise it is very similar to the QCA based RE450.
SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM: 64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS
Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V
Factory image can be uploaded directly through the stock UI.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.
Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).
There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.
This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):
- drop "ignore size" command line option (it was used only for combined
images anyway)
- don't require "flash layout id" for combined images (we don't need and
shouldn't limit size of the initramfs kernel and for kernels inside
safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
needed only for update from vendor GUI and are ingored in case of
initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed
Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
On Asus RT-N12 and RT-N16 models, the WAN and LAN4 ports are swapped in the
initial switch configuration since the presets present in nvram appear to be
wrong.
Add special casing for these models to detect_by_model() in order to ensure
a proper switch configuration.
Fixes FS#502.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Power LED of RB912UAG-{2,5}HPnD boards can be controlled by sofware,
so use it for diag purposes and make the User LED free for other tasks.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
It is quite unexpected behaviour when the Power LED switches off as soon
as the kernel starts booting. So set the default state to 'Keep' for
the Power LEDs of all RouterBOARDs (e.g. RB91x, SXT Lite series, etc.).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[switch the default state to keep instead of on]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't support it currently so there is no
wireless available.
Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1
Issue:
- Wireless radio doesn't work due to the lack of driver.
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
set device and tftp server IP address and input the firmware
file name.U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In the xrx200_close() function we call napi_disable(), that could
sleep, with priv->hw->chan[i].lock held. This could lead to deadlock
and causes the kernel to complain.
Look at the code I couldn't convince myself about why we
need to protect that specific code part with the lock. IMHO there
seems no reason to protect the refcount variables, because AFAIK
ndo_close() and ndo_open() callbacks are already called with a
semaphore held. Neither I could figure out why napi_disable() have to
be called with that lock held. The only remaining code part for
which I could guess the lock is useful for is ltq_dma_close()
function call.
This patch reduces the lock to the said function call, avoiding the
sleep-with-spinlock-held situation
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
[fold into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch, backport to
kernel 4.4]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit f44f1e7da7c8e3f4575d5d61c4df978496903fcc ("um:
Avoid longjmp/setjmp symbol clashes with libpthread.a") to fix build
issues on hosts that only have a static libpthread.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Xen serial console has been broken since the xen_domu subtarget
was merged in the generic x86 subtarget (commits 1d6879ee and 371b382a).
The reason for the broken serial console seems to be an IRQ conflict
between the serial console driver and the PATA_LEGACY driver:
[ 1.330125] genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (platform[pata_legacy.4])
[ 1.330134] hvc_open: request_irq failed with rc -16.
[ 1.330148] Warning: unable to open an initial console.
Just drop the PATA_LEGACY driver from the x86/generic and x86_64
subtargets, since this driver is marked experimental and only supports
very old ISA devices anyway. It is still included in the x86/legacy
subtarget where it rightfully belongs.
Fixes: FS#787
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Xen support for x86/generic was added in 1d6879ee. This commit also
enables it for x86/64.
This was successfully tested with Xen 4.5, although the serial console
is broken in the same way as x86/generic (see FS#787)
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
All x86 subtargets enable USB support, so it makes sense to enable it
in the target config instead, to avoid duplication.
Also refresh subtarget configs accordingly.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This was done by simply running `make kernel_menuconfig CONFIG_TARGET=subtarget`
and then saving without changing any option.
Most of the removed options can be explained because they are already
present in the target config or in the generic 4.9 config:
- PAE-related options, enabled by default on x86 by 961c0eac
- LZO-related options, enabled by default since 4.9
As far as I understand the build system, this shouldn't have any
user-visible impact, because the build system already merges the
various kernel configs during build.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This subtarget was added by 961c0eac, probably by mistake. It does
not contain anything beside a kernel config.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
