The default bootloader partition of some devices is to small for an
u-boot with uncompressed gphy firmware(s).
Instead of increasing the bootloader partition size, in compare to the
stock firmware, compress the firmware. This would allow the bootloader
of at least the FritzBox 3370 as well as the bootloader of the
VGV7510KW22 to fit into the bootloader partition of the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Devices like the xrx200 Arcadyan VGV7519 are using two NOR flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author, all SPI related configs are copy & paste
leftovers. Which makes sense since nothing is connected to the SPI bus
on this device.
The NOR SPL isn't required for this board, since the NOR is directly
memory mapped.
Allow to overwrite the env in ram while using brn variant. Do not set
the power GPIO pin twice.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use:
- 00nn for u-boot patches
- 01nn for new boards
While doing the rework, the board definitions for the easy50712 and
easy80920 were moved to distinct board definitions patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
Explicit sets the size of the mtdparts, because the kernel has also an explicit value.
If they have diffent sizes the ubi won't be detected.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49018
otherwise the uboot is missing important commands like bootz
Signed-off-by: Martin Mueller <mm@sig21.net>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49017
Since switching to new ubi(kernel,squashfs,ubifs) layout, the kernel lies in a
ubi volume. Dropping the mtd parts because the mtd layout is saved in the
device-tree, which is appended to the zImage.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49016
Add support for Xilinx ZC702 Dev board
Zynq target is using 4.4 kernel and mainline 2016.1 u-boot.
Patch is tested with Xilinx ZC702 Dev board with SD boot mode.
known issues:
- no QSPI driver in 4.4 kernel: no QSPI flash support
- USB is not working in 4.4 kernel
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
create mode 100644 package/boot/uboot-zynq/Makefile
create mode 100644 target/linux/zynq/Makefile
create mode 100644 target/linux/zynq/base-files.mk
create mode 100755 target/linux/zynq/base-files/etc/board.d/02_network
create mode 100644 target/linux/zynq/base-files/etc/config/network
create mode 100644 target/linux/zynq/base-files/etc/inittab
create mode 100644 target/linux/zynq/config-4.4
create mode 100644 target/linux/zynq/image/Makefile
create mode 100755 target/linux/zynq/image/mkits.sh
create mode 100644 target/linux/zynq/patches-4.4/0001-arm-dts-zynq-zc702.dts-Set-default-rdinit-to-sbin-in.patch
create mode 100644 target/linux/zynq/profiles/zc702.mk
SVN-Revision: 48697
U-boot ships with the `mx6qsabresd` configuration file to configure a
bootloader suitable for booting the Freescale i.MX6q SABRE evaluation board
from SD card. Expose this option in the uboot-imx6 Makefile.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
SVN-Revision: 48014
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
- tested on Beagleboard C4
- remove upstream patches
- disable THUMB mode on OMAP3 this increases binary size
(remove CONFIG_SYS_THUMB_BUILD)
- reduce SPL size by disabling EXT feature
(remove CONFIG_SPL_EXT_SUPPORT)
this fixes 2015.07 and 2015.10-rc3
Beagleboard C4 booting
which were broken by upstream commit
with id: bd2c4522c26d535515aebca52d27c004a7e0c05c
Arm THUMB mode is broken because of an yet unknown errata
see: http://lists.denx.de/pipermail/u-boot/2015-August/225793.html
- backport upstream fix that was introduced in 2015.10-rc5
and was not fixed in 2015.10 final
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47924
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
Invert the `__GLIBC__` guards into `!__UCLIBC__` ones to avoid
invalid references to `_llseek` on musl.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46125
Add three download mirrors for 'grub', as the Makefile currently defines only
one download location.
@GNU can not be used, as the most recent version of 'grub' is not available
at the general GNU mirrors, and can only be found at the "gnu-alpha" mirrors.
Signed-off-by: Hannu Nyman <hannu.nyman at iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45909
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
After r43987 TARGET_lantiq_xrx200_P2812HNUFX does not exist anymore.
Fix empty menuconfig bootloader selection by making u-boot depend on
one of the new target profiles.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44179
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43508
fixes BeagleBoard C4 detection
error message in serial console was:
"WARNING: Could not determine device tree to use"
change is found in upstream u-boot
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 43392
This adds support for the oxnas target in U-Boot 2014.04
History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10
changes from 2013.10 to 2014.04 can be followed at
https://gitorious.org/openwrt-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43389
This will ease adding new targets and updating:
* split UBOOTS var into multiple lines
* remove version from TITLE
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 43187
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
configure enables libzfs support on default.
This will break the build, on systems without libzfs.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
SVN-Revision: 41935
Generate the configuration file for uboot-envtools
on BTHOMEHUBV2B. Adds the specific parameters for the
BTHOMEHUBV2B and also fixes an incorrect path which
would have affected other lantiq boards as well
(currently only the GIGASX76X).
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41597
Insert a missing #ifdef UBI around the use of libubi_close().
As the preceding if (libubi) will never be true on non-UBI builds,
compiling only failed when disabling optimization.
Also rebase patch to latest u-boot.git HEAD.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41313
On UBI enabled devices, U-Boot might store it's environment on
UBI volume(s). Support this in uboot-envtools, so fw_setenv and
fw_printenv can work on these platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40929
The settings require that the OpenWrt provided u-boot is used as either
first or second stage bootloader as it modifies the partitioning scheme
to move the u-boot environment to a separate mtd partition.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 40829
This patch modifies the u-boot config for the Pogoplug E02 to work with
OpenWrt. It also enables building a second stage bootloader image.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 40828
As both of the PKG_SOURCE_URLs within the Apex Makefile appear to be no
longer functional, this patch changes the source URL to the OpenWRT
downloads page. Apologies for resubmitting, but there was a syntax error
in the previous patch ( http://patchwork.openwrt.org/patch/5025 ).
Signed-off-by: Riley Baird <orthogonal@librewrt.org>
[florian: unmangle patch, fix subject]
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 40718
Depend on lantiq board.
ARV7510 depends on ARV4510 because (according to OpenWrt wiki) both boards are identical except for the unsupported WiFi. Moreover, ARV7510 isn't especifically supported and ARV4510 images valid.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40544
By default kobs-ng will use the size of /dev/mtd0 for the IMX bootstreams.
This patch allows overriding that size in order to reserve space at the end
of the mtd partition for u-boot.img in the case of using an SPL bootloader.
For example, to flash an SPL bootloader that loads u-boot.img from 0xe0000
(14MB) offset in a 16MB /dev/mtd0:
kobs-ng init -v -x --search_exponent=1 --chip_0_size=0xe00000 SPL
nandwrite --start=0xe00000 --pad /dev/mtd0 u-boot.img
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40532
Patches created from tree:
git@github.com:danielschwierzeck/u-boot-lantiq.git
v2013.10..u-boot-lantiq-v2013.10-openwrt4
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40482
Tested on:
* Cloud Engines Pogoplug E02
* RaidSonic ICY BOX IB-NAS62x0
* Iomega Iconnect
Some users are avoiding to replace their bootloader, because of that add
support for second stage u-boot image. Having ubifs capable bootloader is
required in order to boot current OpenWrt trunk.
Sample ib62x0 commands for running second stage bootloader:
tftpboot 0x800000 uboot-kirkwood-ib62x0_second_stage/openwrt-kirkwood-ib62x0_second_stage-u-boot.img
bootm 0x800000
Sample ib62x0 commands for flashing second stage bootloader:
tftpboot 0x800000 uboot-kirkwood-ib62x0_second_stage/openwrt-kirkwood-ib62x0_second_stage-u-boot.img
nand erase 0x100000 0x100000 ; nand write 0x800000 0x100000 0x${filesize}
nand read 0x800000 0x100000 0x100000 ; bootm 0x800000
While at it include parallel build support, use alphabetic order of the boards
and introduce common OpenWrt configuration.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by (on ib62x0): Luka Perkov <luka@openwrt.org>
Tested-by (on dockstar): Alexander Couzens <lynxis@fe80.eu>
Tested-by (on iconnect): Wojciech Dubowik <wojciech.dubowik@neratec.com>
CC: Felix Kaechele <heffer@fedoraproject.org>
CC: Wojciech Dubowik <wojciech.dubowik@neratec.com>
CC: Alexander Couzens <lynxis@fe80.eu>
CC: Daniel Engberg <daniel.engberg@pyret.net>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39590
grub-editenv allows to modify grub2 environment files. Add a new package
that build grub2 for the target and packs up grub-editenv.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 36574
Summary:
* remove all files/* (since merged to upstream)
* patches on nand-spl, mmc and lcd driver
Thanks a lot to Xiangfu Liu!
Signed-off-by: Xiangfu Liu <xiangfu@sharism.cc>
SVN-Revision: 35034
