Commit graph

7 commits

Author SHA1 Message Date
Chris Blake
d1c3a9485a apm821xx: Add default packages to NAND target
This moves core router packages to the NAND target, to ensure they are
applied to all images. This change is being done due to an issue found
when flashing the MX60W image, which came without these when built as a
multi image.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-04-26 11:34:14 +02:00
Christian Lamparter
b5638bb64e apm821xx: redo WAN green and yellow LEDs
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-08 11:17:10 +01:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Christian Lamparter
e9f86c6cac apm821xx: backport generic HDD led-triggers for WNDR4700 and MBL
This patch backports the new generic HDD/SDD led-trigger
from 4.8-rc1.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-09-08 13:40:03 +02:00
Felix Fietkau
44c39d5812 apm821xx: add missing default profiles for subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-22 09:48:12 +02:00
Christian Lamparter
9e0fd1b52a apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720
This patch adds support for Netgear Centria N900 WNDR4700/WNDR4720

hardware highlights:

CPU:	AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz)
	Security support, Boot ROM Location NAND wo/ECC 2k page (8 bits)
	32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board:	AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG
DRAM:	256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3)
NAND:	128 MiB (SLC, erase size: 128 KiB, page size: 2048, OOB size: 64)
ETH:	Atheros AR8327N Gigabit Switch (4 x LAN, 1 x WAN)
USB:	2 x 3.0 (Renesas uPD720202K8-711-BAA-A, firmware not included)
SATA:	1 x SATA-II 3.5" Hard Drive Bay for HDDs (DesignWare SATA).
WLAN1:	Atheros AR9380 5GHz 802.11an 3:3x3
WLAN2:	Atheros AR9581 2.4GHz 802.11bgn 3:3x3
SDCARD:	GL827L SD/MMC/MS Flash Card Reader (on internal dwc2 USB 2.0 host)
I2C:	GMT G781 (i2c-0 @ 0x4d - lm90 compatible temperature sensor)
	TC654    (i2c-0 @ 0x1b - Dual PWM fan Speed controller)

WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!

INFO: Since this device only has a NAND chip. I opted for going with
root.squashfs in a UBI volume. There's no squashfs/jffs2 image.

This target produces three images.
  a. netgear factory image
     This image can be used to flash the Netgear WNDR4700 via the
     firmware recovery mechanism and the web admin site.

     The bootloader can be instructed to do a firmware recovery via the
     # fw_recovery
     command. It will start a tftp server and listen on 192.168.1.1
     (the ipaddr variable in u-boot) for incoming, binary tftp clients.
     The firmware recovery mechanism is also started if any of the flash
     content which contains the kernel, device-tree definitions or the
     (fake)rootfs fails to verify or load.

  b. sysupgrade.tar image for sysupgrade
     An sysupgrade will replace the entire current LEDE installation
     with a newer version. This does include the kernel and the ubi rootfs
     partition. The configuration can be carried over automatically as well
     if desired.

     simply copy the sysupgrade.tar to a the WNDR4700 running LEDE and run:

     root@lede:~# sysupgrade sysupgrade.tar

     and let it reboot.

     Note: The devicetree flash area is NOT updated. Until the devicetree
	   definition is stable, this can lead to all sorts of hardware
	   detection problems! So make sure, if you experience issues: try
	   the fw_recovery. If you are unsure whenever this affects you:
	   test if you can reproduce your issue with the initramfs method.
	   As it will always have up-to-date device-tree definitions.

  c. initramfs image for TFTP (for development and testing)
     To use the initramfs method, follow the following steps:
       1) Move the "lede-apm821xx-netgear-WNDR4700-initramfs-kernel.bin"
	  file to to the root directory of your TFTP server.

       2) rename it to wndr4700.bin

       3) On the WNDR4700 - Hit Enter during u-boot and insert:
	  # tftp 400000 wndr4700.bin; run addtty; bootm 400000 -

     This will boot the LEDE image.

     Note: The default tftp server is 192.168.1.7, if you want to change it:
     # setenv serverip 192.168.8.7;

     Note2: The default address for the WNDR4700 is 192.168.1.1:
     # setenv ipaddr 192.168.8.8;

     Note: Connect you tftp server on the last LAN port (not the WAN)

Note: The firmware for the USB 3.0 Host chip is not included anymore.
Therefore the two USB 3.0 ports will not work without the
uPD7070x-firmware package installed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Chris Blake
a57d6e2d47 apm821xx: add support for the Cisco Meraki MR24
This patch adds support for the Cisco Meraki MR24 Access point
to the apm821xx target.

Board:		MR24 - Meraki MR24 Cloud Managed Access Point
CPU:		APM82181 SoC 800 MHz (PLB=200 OPB=100 EBC=100)
Flash size:	32MiB
RAM Size:	128MiB
Wireless:	Atheros AR9380 5.0GHz + Atheros AR9380 2.4GHz
Ethernet ports:	1x Gigabit Atheros AR8035

WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!

For flashing instructions, visit:
<https://github.com/riptidewave93/Openwrt-MR24/blob/master/README.md#flashing>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-07-22 09:48:12 +02:00