This adds uci entries for all ath79 devices for which this already was
the case on ar71xx. Additionally we add the OCEDO Koala as there was no
support in OpenWRT yet.
Signed-off-by: David Bauer <mail@david-bauer.net>
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.
This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users or writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.
Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)
Flash instruction:
Apply factory image via web-gui.
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fixed DTC command not found error while compling uboot-at91. The fix
is to set DTC PATH in uboot-at91 MAKE command.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fetching uboot src from linux4sam/u-boot-at91 github for all at91
target.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
updating to new version v3.8.10 and copying at91bootstrap.bin to bin folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent
libressl version.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Several changes has been made:
+ AES support has been removed by
upstream commit c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit 34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The serial was working before, but not when doing copy&pasting longer
commands in a short time.
Fixes: a4def18f29 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.
This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-Boot now requires GCC > 5
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Also move some options of patch 010 affecting the whole platform
to 010's device only.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.
This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
