The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.
Both is fixed here.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
We don't have any code for enabling it automatically yet but it allows
adding entries manually to the /etc/config/system.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Backport much of the 10.2 firmware features from upstream QCA driver.
This includes ANI support, adaptive CCA, tx-hang workarounds,
and lots of other things.
Not all of this may be enabled at this point, and more code waits to
be backported as time and motivation allows.
* Fix some rate-control issues where ath10k in station mode (at least), would
sometimes get stuck at low rates. This appeared to be a probe related
state machine issue in the firmware, so I added some timeout logic to kick
the state machine if it gets stuck. This signicantly improves throughput
tests with many stations.
* Support configuring WMI WD timeout using SET_SPECIAL API.
* Properly configure the rx-mask on bootup to work around problem found
by Mr. Kazior. This should remove the need to add the driver hack he
posted.
* Allow configuring pdev failed-retry threshold. This is how many consecutive
tx failures the firmware will allow before resetting the wifi chip (not a full
firmware crash).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Adds Sebastian's 160Mhz support (un-tested), remove DMA32 change that
broke some x86 systems, allow setting 10.1 CT firmware keepalive watchdog
timeout, support QCA 9887 hardware, and some other tweaks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This is upstream alternative for LEDE's ledtrig-usbdev. It's main
advantages are:
1) Support for assigning more than 1 USB port to the LED
2) Setting proper state when activating with device already connected
3) FWIW it's an upstream driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
changed install path from /sbin to /usr/sbin to be consistent with other filesystem tools
ext2-3-4 and f2fs tools are in /usr/sbin, for example
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on cns3xxx & imx6.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
iperf upstream added some bugfixes to the already released 2.0.9 version
without changing the filename. This conflicts with old mirrored files
and the hash that we previously used.
To avoid conflict, use a renamed tarball from mirror2.openwrt.org
containing the new upstream changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.
This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.
Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Commit f5c741b5e0 updated procd to a more recent version, but did not
change the hash of the tar. Update it to the one matching the file on
the download servers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The file to patch doesn't exists. Due to the fact that a src directory
exists, the patch was never applied.
With 28502a9 the behaviour was changed and revealed the issue.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is outdated and bad practice, general dependencies should be documented and leave the rest up to the user.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
