Commit graph

88 commits

Author SHA1 Message Date
Roger Pueyo Centelles
5fba0f0c0c ramips: add suport for ZBT APE522II
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-06-22 19:32:06 +02:00
Henryk Heisig
75af981239 ramips/base-files: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Michael Lee
9a4935687d ramips: add support for DuZun DM06
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Yuan Chenmang
b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Cezary Jackiewicz
2965430999 ramips: cleanup for Hame MPR-A2
- disable all ethernet ports except port 0 on MPR-A2

Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.

- don't use a VLAN for the single ethernet port of the MPR-A2

Like A5-V11, this router only has one ethernet port.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 11:03:23 +02:00
Andrew Yong
374cae9e6f ramips: add initial support for SamKnows SK-WB8
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:35 +02:00
Vittorio Gambaletta (VittGam)
1570277094 ramips: Fix alphabetical sorting for 02_network
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
39f035fdc7 ramips: Don't use a VLAN for the single ethernet port of the A5-V11.
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.

Add this router to the VLAN-less config that is used by other single-port routers.

Also fix MAC address detection code since this router has no WAN port.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
ffb7bf7672 ramips: Fix network for routers without VLANs on eth0.
Some routers only have one port, so eth0 is used without VLANs for them.

Revision r47720 introduced some changes, but wrongly confused "enable" with "reset".

VLANs need to be disabled for those routers, and the switch may be reset.

Fix this, by explicitly disabling VLANs instead of resetting the switch for these routers.

Also merge duplicate configuration for the "m2m".

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:12 +02:00
blogic
6b0425a187 ramips: add support for Planex MZK-EX750NP.
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49268
2016-05-10 10:43:12 +02:00
John Crispin
cb049e71cd ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700

wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49247
2016-04-26 11:43:53 +00:00
John Crispin
279eeeb744 ramips: add support for Planex MZK-EX300NP
MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49235
2016-04-26 11:43:06 +00:00
John Crispin
e55d86ef32 ramips: add support for Planex CS-QR10
CS-QR10 is MT7620A based IP Camera.

the camera and sound does not work with kernel 4.4.
 - camera chip is sn9c291.
 - sound chip is wm8960.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49234
2016-04-26 11:43:01 +00:00
John Crispin
30fbc1a4d1 ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
2016-04-21 19:47:08 +00:00
John Crispin
37b50fdb92 ramips: add support for ELECOM WRH-300CR
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.

it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>

SVN-Revision: 49211
2016-04-21 19:46:59 +00:00
John Crispin
99414dbcf1 ramips: Add support for Xiaomi MiWiFi Nano
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

v3  includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds

SVN-Revision: 49024
2016-03-16 09:26:48 +00:00
John Crispin
be79629259 ramips: Add support for GL-MT750
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.

SVN-Revision: 48994
2016-03-10 19:12:10 +00:00
John Crispin
be53e5a154 ramips: Add support for GL-MT300N
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.

SVN-Revision: 48993
2016-03-10 19:12:04 +00:00
John Crispin
96ee39b184 ramips: Add support for GL-MT300A
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.

SVN-Revision: 48992
2016-03-10 19:11:57 +00:00
John Crispin
1b9985cfe2 ramips: add support for Planex MZK-WDPR.
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 48968
2016-03-08 18:11:59 +00:00
John Crispin
43dd2b9965 ramips: Add JCG routers to base-files
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48905
2016-03-04 08:33:09 +00:00
John Crispin
e4dc6acd31 ramips: Incorrect file mode change
Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 48893
2016-03-03 20:24:45 +00:00
John Crispin
96eb5c6fa8 ramips: Added support for ZBT-826 / ZBT-1026
Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826
Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996

Signed-off-by: Jamie Stuart <jamie@onebillion.org>

SVN-Revision: 48865
2016-03-01 09:17:06 +00:00
John Crispin
8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin
9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
John Crispin
de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin
9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
Jo-Philipp Wich
527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich
8f8b702f85 board.d: remove redundant ucidef_set_interfaces_lan_wan() calls
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47722
2015-12-03 17:30:56 +00:00
Jo-Philipp Wich
9b02e73188 board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.

Also removes now superfluous enable and reset arguments.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47721
2015-12-03 17:30:24 +00:00
Jo-Philipp Wich
d17a64c7c0 base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.

This change ...

 * removes the reset and enable arguments from ucidef_add_switch()
 * unconditionally writes reset:1 and enable:1 to JSON
 * converts the three users of nonstandard values to ucidef_add_switch_attr()

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47720
2015-12-03 17:30:08 +00:00
Jo-Philipp Wich
de51026515 ramips: switch ucidef_add_switch_vlan() to ucidef_add_switch_ports()
This migrates the final board.d user of ucidef_add_switch_vlan() to the new
ucidef_add_switch_ports() approach, fixing some logic errors for a few boards
along the way.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47717
2015-12-03 15:46:29 +00:00
John Crispin
8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin
e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin
165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
8fa6927415 ramips: add support for the Asus RP-N53 in the "02_network" boot script
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47345
2015-11-02 10:17:26 +00:00
John Crispin
51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin
c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin
57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin
2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
John Crispin
2f0449419f ramips: fix indentation, case statements structure and optimize base-files/etc/board.d/02_network
The following patch:
 * fixes wrong indentation
 * combines together boards with same configuration
 * removes unnecessary spaces
 * removes empty lines after ";;" and uses only "|\" (for consistency)
 * orders boards alphabetically

in base-files/etc/board.d/02_network script.

One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs().

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46634
2015-08-17 06:02:59 +00:00
John Crispin
0d464c360f ramips: remove old code for Edimax BR-6524N
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46630
2015-08-17 06:01:23 +00:00
John Crispin
e4b6dcee5e ramips: fix Buffalo WMR-300 dts, board, image and profile names
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46628
2015-08-17 06:00:49 +00:00
John Crispin
713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin
102073ca17 ramips: fix Argus ATP-52B board and image names
The following patch:
 * changes board name from "argus-atp52b" to "atp-52b"
 * changes dts filename
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Argus ATP-52B device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46621
2015-08-17 05:58:57 +00:00
John Crispin
a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin
f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00