Adding support 6LoWPAN over Bluetooth Low Energy in kernel 3.18.
Creating new bluetooth_6lowpan group with CONFIG_6LOWPAN and CONFIG_BT_6LOWPAN.
Adding kernel object dependencies for 6LoWPAN over Bluetooth Low Energy.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44084
This restores normal pre-r43715 200ms blink-period for the System LED we're all accustomed to see while our OpenWrt routers are booting.
Failsafe possibility will now be signalled with a new 100ms blinking, which is easily recognizable from the normal 200ms booting.
So no existing user will be scared by a new 500ms LED pattern, since such a slow pattern could easily be mistaken for something wrong... I was like "ok why my router is collapsing now, is this a bad flash, a kernel panic, or what else" when I've seen it for the first time ;)
Sorry for not having explained myself better in v1 of this patch.
Original:
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 200ms
Failsafe entered: 50ms
Now (after preinit_regular has been introduced):
Preinit, failsafe is possible: 200ms
Preinit, failsafe not possible anymore, booting normally: 500ms *here is the "offending" change*
Failsafe entered: 50ms
With my proposed patch:
Preinit, failsafe is possible: 100ms *indicate this condition with a new timing, that prompts the user to press the key if they want to start failsafe*
Preinit, failsafe not possible anymore, booting normally: 200ms *keep this as before*
Failsafe entered: 50ms
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44056
Some Huawei mobile broadband sticks utilizing the NCM protocol expose
the control channel as a cdc-wdm device node instead of a virtual TTY.
This device node does not support the terminal ioctls. This patch
adds a check whether the provided device is a TTY or not and does not
attempt to use the terminal ioctls if they are not supported.
v2: reduce diffstat by simplifying code a little
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44054
This patch adds a simple check to silence logging of messages about
unrecognized igmp packets which originate from devices in local network.
Without this patch igmpproxy floods openwrt syslog with messages such as:
user.warn igmpproxy[19818]: The source address 192.168.1.175 for group
239.255.250.250, is not in any valid net for upstream VIF.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44020
The --quiet-dhcp setting increases privacy by omitting DHCP lease logs including MAC addresses.
Signed-off-by: Lars Kruse <devel@sumpfralle.de>
SVN-Revision: 44006
Introduce configuration options to build an "hardened" OpenWRT.
Options to enable Stack-Smashing Protection, FORTIFY_SOURCE and RELRO
have been introduced.
uClibc makefile now automatically detects if SSP support is necessary.
hostapd makefile has been fixed to use "^" as sed separator since
using a comma was problematic when using "-Wl,-z,now" and the like in
TARGET_CFLAGS.
Currently enabling SSP on user space depends on enabling SSP kernel
side, this is due to the fact that TARGET_CFLAGS are used to build
kernel modules (at least). Suggestions on how to avoid this are welcome.
Using "select" instead of "depends on" doesn't seem to work with choice
entries.
Tested with a lantiq (WBMR) router, GCC 4.8, uClibc and a subset of
the available packages.
Needs to be tested with GCC 4.9 and the remaining packages.
PIE not currently included.
Signed-off-by: Alessandro Di Federico <ale+owrt@clearmind.me>
SVN-Revision: 44005
Otherwise libatomic cannot be used in conjunction with external toolchains.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 43998
iproute2 includes "sanitized" linux kernel headers, which work fine for uClibc, however
with musl there is some header conflict, principally some ipv6 structure redefinition. This
patch removes <linux/in6.h> from include/linux/if_bridge.h to solve the problem.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 43992
Add documentation that makes it easier to find the alternative,
recommended, and default handling for buttons in OpenWrt.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
SVN-Revision: 43989
This patch fixes adding new stations for some specific drivers when
using more than 1 BSS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43951
The enable and reset settings need to be added even when they're false. This is true at least for 'enable', that seems to default to true otherwise.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43887
Makes sure that the openvpn instance gets restarted in case of a crash.
Intentional stops using /etc/init.d/openvpn stop will not result in
respawning. Anything else will, e.g. killall openvpn.
Signed-off-by: Lars Gierth <larsg@systemli.org>
SVN-Revision: 43886
Change the kconfig default for the repository url template to use "%s"
instead of "%T" as well.
Also complete the kconfig help text do cover the recently introduced
manufacturer, product and hwrev options.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43872
This commit introduces a new option CONFIG_VERSION_FILENAMES which causes
OpenWrt to embed the version number in generated image files, SDK- and
ImageBuilder archives.
The option is enabled by default if CONFIG_VERSIONOPT is set.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43869
This patch tries to
- Let the DHCPv6 feature depend on CONFIG_IPV6.
- Conditionally select libnettle, kmod-ipv6, kmod-ipt-ipset only if the
corresponding features are enabled.
- Install `trust-anchors.conf` only if DNSSEC is selected.
- Add PKG_CONFIG_DEPENDS for the configurable options.
- Add a patch to let the Makefile of dnsmasq be aware of changes in
COPTS variable.
Big thanks goes to Frank Schäfer <fschaefer.oss@googlemail.com> for
providing necessary information on connections and dependency relations
between these CONFIGs and packages.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 43851
Target pxcab and ps3 were removed from maintaince in r34764 and r34765
respectively.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 43850
The uapsd option sets the uapsd_advertisement_enabled flag in hostapd.
The check for phy support is already implemented here in hostapd since 2011:
http://w1.fi/cgit/hostap/commit/?id=70619a5d8a3d32faa43d66bcb1b670cacf0c243e
So this can be safely set to 1 as default.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43846
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
fixes a bug where wdt write happened with no valid fd available
--> procd: WDT failed to write: Bad file descriptor
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43711
Commit ce92f6650bd8a86db04c7a6cbb58e7fdb200a7e6 added source IP support
for DHCP default routes. As a side effect of this change the default route
could be present twice in netifd (once with source IP set and once with
source IP unset) if it was sent by the server in both the router and static
route options. Therefore add source IP support as well for static routes as this
case was not considered. Additional remove unused parameter type.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 43645
Apply libnl commit 807fddc4cd9ecb12ba64e1b7fa26d86b6c2f19b0 ("nl:
Increase receive buffer size to 4 pages") also to libnl-tiny to ensure
netlink messages larger than 4KiB can be received, as the restart logic
seems to be broken.
This fixes iwinfo accessing info on dual band b43 cards, as they can
support a lot of channels, breaking the 4K default limit (seen was >5k).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43633
The kernel build system cannot track dependencies of out-of-tree
modules, making the buildsystem fail to load mac80211.
Add mac80211 as an explicit load to ensure all required modules are
loaded.
Fixes#16522.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43631
it should needs to depend on imx and mxs
also remove duplicate kmod definition from mxs target
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43627
I have not found a scenario that would break by setting the source address on
default, but please let me know if any special considerations should be taken.
Signed-off-by: Kristian Evensen <kristian.evensen at gmail.com>
SVN-Revision: 43582
if the initramfs kernel and payload were flashed in one block, the payload might not be at the start of the ubi partition due to bad blocks inside the kernel partition.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43513
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43508
it is now possible to flash a initramfs kernel and a sysupgrade tar file inside the ubi partition. on first boot, the takeover script will find the tar file, extract and finally sysupgrade it. this allows us to flash owrt/ubi images in a 2 phase setup using ODM webuis that are not ubi aware. this is needed by some mediatek and brokencom devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43505
this can be used on nand flashes and will skip bad blocks and run ecc on the
read data before dumping it.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43500
Added complementary blobmsg_close_table() before returning from function
on error.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
SVN-Revision: 43477
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
create user:group before running postinst-pkg. the postinst hook might require
the user:group to already exist.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 43472
Packages fdisk and lsblk were missing dependency for libsmartcols.so.1
Add package for libsmartcols and add dependency from fdisk and lsblk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43459
perf was in the oldpackages repository, but it makes more sense to have
it part of the default package set since we build it from the Linux
kernel sources.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43418
Thanks to Dave Taht for debugging and thanks to Comcast for
shipping strangely behaving software so I can fix some corner cases.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 43415
fixes BeagleBoard C4 detection
error message in serial console was:
"WARNING: Could not determine device tree to use"
change is found in upstream u-boot
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 43392
This adds support for the oxnas target in U-Boot 2014.04
History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10
changes from 2013.10 to 2014.04 can be followed at
https://gitorious.org/openwrt-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43389
This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
Oxford Semiconductor OXE810SE/OXE815/OX820/...
For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
fully supported
Cloud Engines Pogoplug Pro (with PCIe)
fully supported
MitraStar STG-212
aka ZyXEL NSA-212,
aka Medion Akoya P89625 / P89636 / P89626 / P89630,
aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
fully supported, see http://wiki.openwrt.org/toh/medion/md86587
Shuttle KD-20
partially supported (S-ATA driver lacks support for 2nd port)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43388
mtd.c:544:7: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘ssize_t’ [-Wformat]
mtd.c:602:1: warning: label ‘done’ defined but not used [-Wunused-label]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43383
1) nand_upgrade_tar: use a simpler condition that matches if () { }
logic and fix check of $kernel_length variable
2) nand_do_upgrade_stage2: use case, otherwise one could believe we
always call nand_upgrade_tar
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43373
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
ld-musl-*.so* is a symlink "broken" for the hostsystem, so wildcard
will skip it, causing LD_MUSL_NAME to empty and the ldd symlink pointing
to ../../lib directly.
This causes sysupgrade failing to copy any linked libaries and
consequently failing to run anything after switching to ram disk.
Fix this by creating a symlink directly pointing to where ld-musl-*.so*
points to.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43314
Update nf_conntrack_rtsp to latest version based on http://mike.it-loops.com/rtsp/ (rtsp-module-3.7-v2.tar.gz).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43311
* fixes a bug in multipart sms
* adds a new call to read the sim phone number (partially functioanl)
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43310
r36107 ("base-files: sysupgrade fail with eglibc") tried to fix
sysupgrade by changing the ld-soname to what is expected, but only
fixed MIPS while breaking ARM.
The underlying issue is that the ld.so name varies widely across
different architectures for eglibc:
eglibc-2.19-r25243$ grep -r "ld-soname :=" . | awk '{ print $3 }' | sort -u
ld64.so.1
ld64.so.2
ld-linux-aarch64_be.so.1
ld-linux-aarch64.so.1
ld-linux-armhf.so.3
ld-linux-mipsn8.so.1
ld-linux.so.2
ld-linux.so.3
ld-linux-x32.so.2
ld-linux-x86-64.so.2
ld.so.1
Instead of adding each different soname to check for and copy it,
replace the awk script with a sed script to extract it properly and
drop the hardcoded so-name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43295
Starting from kernel version 3.15, the crc32c module was renamed to
crc32c_generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43291
usb-common.ko was moved to drivers/usb/common starting from kernel 3.16
by upstream commit f4cbd33fd5f0587910fa9db403a1b42f1cabf820
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43290
