diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 9a714ddc69..ac97d037c1 100644
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -68,6 +68,10 @@ case "$FIRMWARE" in
 		rt2x00_eeprom_extract "factory" 0 272
 		;;
 
+	wl341v3)
+		rt2x00_eeprom_extract "board-nvram" 64880 272
+		;;
+
 	*)
 		rt2x00_eeprom_die "board $board is not supported yet"
 		;;
diff --git a/target/linux/ramips/base-files/etc/uci-defaults/network b/target/linux/ramips/base-files/etc/uci-defaults/network
index cc5600bcfd..bce24e8432 100755
--- a/target/linux/ramips/base-files/etc/uci-defaults/network
+++ b/target/linux/ramips/base-files/etc/uci-defaults/network
@@ -111,6 +111,11 @@ ramips_setup_macs()
                 wan_mac=$(ramips_get_mac_binary factory 40)
 		;;
 
+	wl341v3)
+		lan_mac=$(ramips_get_mac_binary board-nvram 65440)
+		wan_mac=$(/usr/sbin/maccalc add "$lan_mac" 1)
+		;;
+
 	wli-tx4-ag300n)
 		lan_mac=$(ramips_get_mac_binary factory 4)
 		;;
diff --git a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac
index 9a4d515b19..f6884c8477 100644
--- a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac
+++ b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac
@@ -29,6 +29,10 @@ preinit_set_mac_address() {
 		mac=$(ramips_get_mac_binary factory 40)
 		ifconfig eth0 hw ether $mac 2>/dev/null
 		;;
+	wl341v3)
+		mac=$(ramips_get_mac_binary board-nvram 65440)
+		ifconfig eth0 hw ether $mac 2>/dev/null
+		;;
 	esac
 }
 
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index ca9b3c9cfc..b3c54e82db 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -113,6 +113,9 @@ ramips_board_name() {
 	*"WHR-G300N")
 		name="whr-g300n"
 		;;
+	*"Sitecom WL-341 v3")
+		name="wl341v3"
+		;;
 	*"Sitecom WL-351 v1 002")
 		name="wl-351"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 30754b5c2f..494e774ef9 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -30,6 +30,7 @@ platform_check_image() {
 	rt-n15 | \
 	w502u |\
 	v22rw-2x2 | \
+	wl341v3 | \
 	wli-tx4-ag300n | \
 	whr-g300n |\
 	wr512-3gn)
diff --git a/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h b/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h
index 272e2b818e..bec6ff0bec 100644
--- a/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h
+++ b/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h
@@ -42,6 +42,7 @@ enum ramips_mach_type {
 	RAMIPS_MACH_W502U,		/* ALFA Networks W502U */
 	RAMIPS_MACH_WCR150GN,		/* Sparklan WCR-150GN */
 	RAMIPS_MACH_WHR_G300N,		/* Buffalo WHR-G300N */
+	RAMIPS_MACH_WL341V3,		/* Sitecom WL-341 v3 */
 	RAMIPS_MACH_WL351,		/* Sitecom WL-351 v1 002 */
 	RAMIPS_MACH_WR512_3GN,		/* SH-WR512NU/WS-WR512N1-like 3GN*/
 };
diff --git a/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig b/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig
index 45d6cd307a..826a484fe9 100644
--- a/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig
+++ b/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig
@@ -86,6 +86,11 @@ config RT305X_MACH_V22RW_2X2
 	select RALINK_DEV_GPIO_BUTTONS
 	select RALINK_DEV_GPIO_LEDS
 
+config RT305X_MACH_WL341V3
+	bool "Sitecom WL-341 v3 board support"
+	select RALINK_DEV_GPIO_BUTTONS
+	select RALINK_DEV_GPIO_LEDS
+
 config RT305X_MACH_WL351
 	bool "Sitecom WL-351 support"
 	select RALINK_DEV_GPIO_BUTTONS
diff --git a/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile b/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile
index 5a45412e5c..743493e80b 100644
--- a/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile
+++ b/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile
@@ -30,4 +30,5 @@ obj-$(CONFIG_RT305X_MACH_W502U)		+= mach-w502u.o
 obj-$(CONFIG_RT305X_MACH_WCR150GN)	+= mach-wcr150gn.o
 obj-$(CONFIG_RT305X_MACH_WHR_G300N)	+= mach-whr-g300n.o
 obj-$(CONFIG_RT305X_MACH_WR512_3GN)	+= mach-wr512-3gn.o
+obj-$(CONFIG_RT305X_MACH_WL341V3)	+= mach-wl341v3.o
 obj-$(CONFIG_RT305X_MACH_WL351)		+= mach-wl351.o
diff --git a/target/linux/ramips/files/arch/mips/ralink/rt305x/mach-wl341v3.c b/target/linux/ramips/files/arch/mips/ralink/rt305x/mach-wl341v3.c
new file mode 100644
index 0000000000..9341be3bee
--- /dev/null
+++ b/target/linux/ramips/files/arch/mips/ralink/rt305x/mach-wl341v3.c
@@ -0,0 +1,154 @@
+/*
+ *  Sitecom WL341v3 board support
+ *
+ *  Copyright (C) 2012 Marco Antonio Mauro <marcus90@gmail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-ralink/machine.h>
+#include <asm/mach-ralink/dev-gpio-buttons.h>
+#include <asm/mach-ralink/dev-gpio-leds.h>
+#include <asm/mach-ralink/rt305x.h>
+#include <asm/mach-ralink/rt305x_regs.h>
+
+#include "devices.h"
+
+#define WL341V3_GPIO_LED_FIRST_AMBER	9
+#define WL341V3_GPIO_LED_FIRST_BLUE	13
+#define WL341V3_GPIO_LED_THIRD_AMBER	11
+#define WL341V3_GPIO_LED_THIRD_BLUE	14
+#define WL341V3_GPIO_LED_FOURTH_BLUE	10
+#define WL341V3_GPIO_LED_FIFTH_AMBER	12
+#define WL341V3_GPIO_LED_FIFTH_BLUE	8
+
+#define WL341V3_GPIO_BUTTON_WPS		5	/* active low */
+#define WL341V3_GPIO_BUTTON_RESET	7	/* active low */
+
+#define WL341V3_BUTTONS_POLL_INTERVAL	20
+
+#ifdef CONFIG_MTD_PARTITIONS
+static struct mtd_partition wl341v3_partitions[] = {
+	{
+		.name	= "u-boot",
+		.offset	= 0,
+		.size	= 0x020000,
+		.mask_flags = MTD_WRITEABLE,
+	}, {
+		.name	= "board-nvram",
+		.offset	= 0x020000,
+		.size	= 0x010000,
+		.mask_flags = MTD_WRITEABLE,
+	}, {
+		.name	= "u-boot-env",
+		.offset	= 0x030000,
+		.size	= 0x010000,
+		.mask_flags = MTD_WRITEABLE,
+	}, {
+		.name	= "kernel",
+		.offset	= 0x040000,
+		.size	= 0x0d0000,
+	}, {
+		.name	= "rootfs",
+		.offset	= 0x110000,
+		.size	= 0x2e0000,
+	}, {
+		.name	= "signature-eRcOmM",
+		.offset	= 0x3f0000,
+		.size	= 0x010000,
+	}, {
+		.name	= "firmware",
+		.offset	= 0x040000,
+		.size	= 0x3b0000,
+	}, {
+		.name	= "fullflash",
+		.offset	= 0x000000,
+		.size	= 0x400000,
+	}
+};
+#endif /* CONFIG_MTD_PARTITIONS */
+
+static struct physmap_flash_data wl341v3_flash_data = {
+#ifdef CONFIG_MTD_PARTITIONS
+	.nr_parts	= ARRAY_SIZE(wl341v3_partitions),
+	.parts		= wl341v3_partitions,
+#endif
+};
+
+static struct gpio_led wl341v3_leds_gpio[] __initdata = {
+	{
+		.name		= "wl341v3:amber:first",
+		.gpio		= WL341V3_GPIO_LED_FIRST_AMBER,
+		.active_low	= 1,
+	}, {
+		.name		= "wl341v3:blue:first",
+		.gpio		= WL341V3_GPIO_LED_FIRST_BLUE,
+		.active_low	= 1,
+	}, {
+		.name		= "wl341v3:amber:third",
+		.gpio		= WL341V3_GPIO_LED_THIRD_AMBER,
+		.active_low	= 1,
+	}, {
+		.name		= "wl341v3:blue:third",
+		.gpio		= WL341V3_GPIO_LED_THIRD_BLUE,
+		.active_low	= 1,
+	}, {
+		.name		= "wl341v3:blue:fourth",
+		.gpio		= WL341V3_GPIO_LED_FOURTH_BLUE,
+		.active_low	= 1,
+	}, {
+		.name		= "wl341v3:amber:fifth",
+		.gpio		= WL341V3_GPIO_LED_FIFTH_AMBER,
+		.active_low	= 1,
+	}, {
+		.name		= "wl341v3:blue:fifth",
+		.gpio		= WL341V3_GPIO_LED_FIFTH_BLUE,
+		.active_low	= 1,
+	}
+};
+
+static struct gpio_button wl341v3_gpio_buttons[] __initdata = {
+	{
+		.desc		= "reset",
+		.type		= EV_KEY,
+		.code		= KEY_RESTART,
+		.threshold	= 3,
+		.gpio		= WL341V3_GPIO_BUTTON_RESET,
+		.active_low	= 1,
+	}, {
+		.desc		= "wps",
+		.type		= EV_KEY,
+		.code		= KEY_WPS_BUTTON,
+		.threshold	= 3,
+		.gpio		= WL341V3_GPIO_BUTTON_WPS,
+		.active_low	= 1,
+	}
+};
+
+static void __init wl341v3_init(void)
+{
+	rt305x_gpio_init(RT305X_GPIO_MODE_GPIO << RT305X_GPIO_MODE_UART0_SHIFT);
+
+	rt305x_register_flash(0, &wl341v3_flash_data);
+	rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_WLLLL;
+	rt305x_register_ethernet();
+	ramips_register_gpio_leds(-1, ARRAY_SIZE(wl341v3_leds_gpio),
+				  wl341v3_leds_gpio);
+	ramips_register_gpio_buttons(-1, WL341V3_BUTTONS_POLL_INTERVAL,
+				     ARRAY_SIZE(wl341v3_gpio_buttons),
+				     wl341v3_gpio_buttons);
+	rt305x_register_wifi();
+	rt305x_register_wdt();
+	rt305x_register_usb();
+}
+
+MIPS_MACHINE(RAMIPS_MACH_WL341V3, "WL341V3", "Sitecom WL-341 v3",
+	     wl341v3_init);
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index c6b214ff36..745edefbae 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -67,6 +67,28 @@ define BuildFirmware/Generic
 	fi; fi
 endef
 
+define BuildFirmware/WL341V3
+	$(call PatchKernelLzma,$(2),$(3) $($(4)))
+	$(call MkImage,lzma,"$(KDIR)/vmlinux-$(2).bin.lzma","$(KDIR)/vmlinux-$(2).uImage")
+	if [ `stat -c%s "$(KDIR)/vmlinux-$(2).uImage"` -gt $(5) ]; then \
+		echo "Warning: $(KDIR)/vmlinux-$(2).uImage is too big"; \
+	else if [ `stat -c%s $(KDIR)/root.$(1)` -gt $(6) ]; then \
+		echo "Warning: $(KDIR)/root.$(1) is too big"; \
+	else \
+		( \
+			dd if=/dev/zero bs=195936 count=1; \
+			echo "1.01"; \
+			dd if=/dev/zero bs=581 count=1; \
+			echo -n -e "\x73\x45\x72\x43\x6F\x4D\x6D\x00\x01\x00\x00\x59\x4E\x37\x95\x58\x10\x00\x20\x00\x28\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x11\x03\x00\x00\x80\x00\x00\x00\x00\x03\x00\x00\x10\x12\x00\x00\x00\x10\x73\x45\x72\x43\x6F\x4D\x6D"; \
+			dd if=/dev/zero bs=65552 count=1; \
+			dd if=$(KDIR)/vmlinux-$(2).uImage bs=$(5) conv=sync; \
+			dd if=$(KDIR)/root.$(1) bs=64k conv=sync; \
+			dd if=/dev/zero bs=`expr 4194304 - 262144 - 16 - $(5) - \( \( \( \`stat -c%s $(KDIR)/root.$(1)\` / 65536 \) + 1 \) \* 65536 \)` count=1; \
+			echo -n -e "\x11\x03\x80\x00\x10\x12\x90\xF7\x65\x52\x63\x4F\x6D\x4D\x00\x00"; \
+		) > $(call imgname,$(1),$(2))-factory.bin; \
+	fi; fi
+endef
+
 define BuildFirmware/Buffalo
 	$(call PatchKernelLzma,$(2),board=$(3) $($(4)))
 	$(call MkImage,lzma,"$(KDIR)/vmlinux-$(2).bin.lzma","$(KDIR)/vmlinux-$(2).uImage")
@@ -151,6 +173,16 @@ define Image/Build/Template/OMNIEMB
 	$(call BuildFirmware/Generic,$(1),$(2),board=$(3) console=$(console_OMNIEMB),mtdlayout_OMNIEMB,1048576,7012352)
 endef
 
+mtdlayout_sercomm_4M=mtdparts=physmap-flash.0:128k(u-boot)ro,64k(board-nvram)ro,64k(u-boot-env)ro,832k(kernel),2944k(rootfs),64k(signature-eRcOmM),3776k@0x40000(firmware),4096k@0x0(fullflash)
+define Image/Build/Template/WL341V3
+	$(call BuildFirmware/Generic,$(1),$(2),board=$(3),mtdlayout_sercomm_4M,851968,3014656)
+	$(call BuildFirmware/WL341V3,$(1),$(2),board=$(3),mtdlayout_sercomm_4M,851968,3014656)
+endef
+
+define Image/Build/Profile/WL341V3
+	$(call Image/Build/Template/WL341V3,$(1),wl341v3,WL341V3)
+endef
+
 define Image/Build/Profile/DIR300B1
 	$(call Image/Build/Template/DIR300B1,$(1),dir-300-b1,DIR-300-B1,wrgn23_dlwbr_dir300b)
 	$(call Image/Build/Template/DIR300B1,$(1),dir-600-b1,DIR-600-B1,wrgn23_dlwbr_dir600b)
@@ -294,6 +326,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/MOFI35003GN,$(1))
 	$(call Image/Build/Profile/W502U,$(1))
 	$(call Image/Build/Profile/WR5123GN,$(1))
+	$(call Image/Build/Profile/WL341V3,$(1))
 	$(call Image/Build/Profile/WL351,$(1))
 endef
 endif
diff --git a/target/linux/ramips/rt305x/config-2.6.39 b/target/linux/ramips/rt305x/config-2.6.39
index 891a421d2d..e9ef379c07 100644
--- a/target/linux/ramips/rt305x/config-2.6.39
+++ b/target/linux/ramips/rt305x/config-2.6.39
@@ -109,6 +109,7 @@ CONFIG_RT305X_MACH_V22RW_2X2=y
 CONFIG_RT305X_MACH_W502U=y
 CONFIG_RT305X_MACH_WCR150GN=y
 CONFIG_RT305X_MACH_WHR_G300N=y
+CONFIG_RT305X_MACH_WL341V3=y
 CONFIG_RT305X_MACH_WL351=y
 CONFIG_RT305X_MACH_WR512_3GN=y
 # CONFIG_SCSI_DMA is not set