pxa: add support for 3.3

SVN-Revision: 31641

target/linux/pxa/config-3.3

@@ -0,0 +1,210 @@
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
+CONFIG_ARCH_GUMSTIX=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
+# CONFIG_ARCH_LUBBOCK is not set
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_ARCH_NR_GPIO=0
+# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_ARCH_PXA_V7 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+# CONFIG_ARCH_USES_GETTIMEOFFSET is not set
+# CONFIG_ARCH_VIPER is not set
+CONFIG_ARM=y
+# CONFIG_ARM_CPU_SUSPEND is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+CONFIG_ARM_NR_BANKS=8
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_THUMB is not set
+# CONFIG_ARPD is not set
+CONFIG_ATA=m
+# CONFIG_ATMEL_PWM is not set
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_BCMA_POSSIBLE=y
+CONFIG_BLK_DEV_IDECS=m
+# CONFIG_BLK_DEV_IDEDMA is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CMDLINE="rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
+CONFIG_CMDLINE_FROM_BOOTLOADER=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_HAS_PMU=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_USE_DOMAINS=y
+CONFIG_CPU_XSCALE=y
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_LL_UART_NONE is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DW_WATCHDOG is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_EPOLL is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_GENERIC_CPU_DEVICES is not set
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_PXA=y
+# CONFIG_HAMRADIO is not set
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_AOUT=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_WORK=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_HAVE_KERNEL_XZ=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SCHED_CLOCK=y
+CONFIG_HAVE_SPARSE_IRQ=y
+CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_PXA=m
+# CONFIG_I2C_PXA_PCI is not set
+CONFIG_I2C_PXA_SLAVE=y
+CONFIG_IDE=m
+CONFIG_IWMMXT=y
+CONFIG_KTIME_SCALAR=y
+# CONFIG_LEDS_GPIO is not set
+# CONFIG_MACH_ARCOM_ZEUS is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_BALLOON3 is not set
+# CONFIG_MACH_CAPC7117 is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_GUMSTIX_F is not set
+CONFIG_MACH_GUMSTIX_VERDEX=y
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_ICONTROL is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_MACH_RAUMFELD_CONNECTOR is not set
+# CONFIG_MACH_RAUMFELD_RC is not set
+# CONFIG_MACH_RAUMFELD_SPEAKER is not set
+# CONFIG_MACH_SAAR is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_VPAC270 is not set
+# CONFIG_MACH_XCEP is not set
+# CONFIG_MACH_ZIPIT2 is not set
+# CONFIG_MACH_ZYLONITE300 is not set
+# CONFIG_MACH_ZYLONITE320 is not set
+CONFIG_MDIO_BOARDINFO=y
+# CONFIG_MFD_T7L66XB is not set
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_PXA=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+CONFIG_MTD_CFI_GEOMETRY=y
+# CONFIG_MTD_CFI_I2 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PXA2XX=y
+# CONFIG_MTD_XIP is not set
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+# CONFIG_PACKET is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PATA_PCMCIA=m
+# CONFIG_PATA_PXA is not set
+CONFIG_PCCARD=m
+# CONFIG_PCI_SYSCALL is not set
+CONFIG_PCMCIA=m
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_PXA2XX=m
+CONFIG_PCMCIA_SOC_COMMON=m
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PHYLIB=y
+CONFIG_PLAT_PXA=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_PXA27x=y
+# CONFIG_PXA_EZX is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_QUOTACTL is not set
+CONFIG_SA1100_WATCHDOG=m
+CONFIG_SCSI=m
+CONFIG_SCSI_MOD=m
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_PROC_FS is not set
+# CONFIG_SDIO_UART is not set
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIO=m
+CONFIG_SERIO_LIBPS2=m
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=m
+CONFIG_SMC911X=m
+CONFIG_SMC91X=m
+CONFIG_SMSC911X=y
+# CONFIG_SMSC911X_ARCH_HOOKS is not set
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+# CONFIG_TRIZEPS_PXA is not set
+CONFIG_UID16=y
+CONFIG_UNIX=m
+CONFIG_VECTORS_BASE=0xffff0000
+# CONFIG_VLAN_8021Q is not set
+CONFIG_XSCALE_PMU=y
+CONFIG_XZ_DEC=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZONE_DMA_FLAG=0

target/linux/pxa/patches-3.3/001-gumstix_verdex_pro_arch_support.patch

@@ -0,0 +1,881 @@
+From 4f4bb58cba3a6c44e9f9f113609287d9d50be9c4 Mon Sep 17 00:00:00 2001
+From: Joseph Kortje <jpktech@rogers.com>
+Date: Wed, 28 Oct 2009 21:11:28 -0400
+Subject: [PATCH] [ARM] Gumstix Verdex Pro arch support
+
+add an option for Verdex Pro when ARCH_GUMSTIX is selected, and
+factor earlier Gumstix support into a seperate option
+
+Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
+---
+ arch/arm/mach-pxa/Kconfig                   |   29 +-
+ arch/arm/mach-pxa/Makefile                  |    3 +-
+ arch/arm/mach-pxa/gumstix-verdex.c          |  749 +++++++++++++++++++++++++++
+ arch/arm/mach-pxa/include/mach/mfp-pxa27x.h |    1 +
+ 4 files changed, 772 insertions(+), 10 deletions(-)
+ create mode 100644 arch/arm/mach-pxa/gumstix-verdex.c
+
+--- a/arch/arm/mach-pxa/Kconfig
++++ b/arch/arm/mach-pxa/Kconfig
+@@ -134,23 +134,34 @@ config MACH_CAPC7117
+ 	select PXA3xx
+ 
+ config ARCH_GUMSTIX
+-	bool "Gumstix XScale 255 boards"
+-	select PXA25x
++	bool "Gumstix boards"
+ 	help
+-	  Say Y here if you intend to run this kernel on
+-	  Basix, Connex, ws-200ax, ws-400ax systems
++        Say Y here if you intend to run this kernel on a
++	  gumstix computer.
+ 
+-choice
+-	prompt "Gumstix Carrier/Expansion Board"
+ 	depends on ARCH_GUMSTIX
+ 
+-config GUMSTIX_AM200EPD
++config MACH_GUMSTIX_F
++	bool "Gumstix Basix/Connex ..."
++	depends on ARCH_GUMSTIX
++	select PXA25x
++
++ choice
++	prompt "Gumstix Carrier/Expansion Board"
++	depends on MACH_GUMSTIX_F
++
++ config GUMSTIX_AM200EPD
+ 	bool "Enable AM200EPD board support"
+ 
+-config GUMSTIX_AM300EPD
++ config GUMSTIX_AM300EPD
+ 	bool "Enable AM300EPD board support"
+ 
+-endchoice
++ endchoice
++
++config MACH_GUMSTIX_VERDEX
++	bool "Gumstix VERDEX ..."
++	depends on ARCH_GUMSTIX
++	select PXA27x
+ 
+ config MACH_INTELMOTE2
+ 	bool "Intel Mote 2 Platform"
+--- a/arch/arm/mach-pxa/Makefile
++++ b/arch/arm/mach-pxa/Makefile
+@@ -51,7 +51,8 @@ endif
+ obj-$(CONFIG_MACH_EM_X270)	+= em-x270.o
+ obj-$(CONFIG_MACH_CM_X300)      += cm-x300.o
+ obj-$(CONFIG_MACH_CAPC7117)     += capc7117.o mxm8x10.o
+-obj-$(CONFIG_ARCH_GUMSTIX)	+= gumstix.o
++obj-$(CONFIG_MACH_GUMSTIX_F)	+= gumstix.o
++obj-$(CONFIG_MACH_GUMSTIX_VERDEX)	+= gumstix-verdex.o
+ obj-$(CONFIG_GUMSTIX_AM200EPD)	+= am200epd.o
+ obj-$(CONFIG_GUMSTIX_AM300EPD)	+= am300epd.o
+ obj-$(CONFIG_MACH_INTELMOTE2)	+= stargate2.o
+--- /dev/null
++++ b/arch/arm/mach-pxa/gumstix-verdex.c
+@@ -0,0 +1,793 @@
++/*
++ *  linux/arch/arm/mach-pxa/gumstix-verdex.c
++ *
++ *  Support for the Gumstix verdex motherboard.
++ *
++ *  Original Author:  Craig Hughes
++ *  Created:          Feb 14, 2008
++ *  Copyright:        Craig Hughes
++ *
++ *  This program is free software; you can redistribute it and/or modify
++ *  it under the terms of the GNU General Public License version 2 as
++ *  published by the Free Software Foundation.
++ *
++ *  Implemented based on lubbock.c by Nicolas Pitre and code from Craig
++ *  Hughes
++ */
++
++#include <linux/module.h>
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/interrupt.h>
++#include <linux/mtd/mtd.h>
++#include <linux/mtd/partitions.h>
++#include <linux/i2c/tsc2007.h>
++#include <linux/i2c/pxa-i2c.h>
++#include <linux/gpio.h>
++
++#include <asm/setup.h>
++#include <asm/memory.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++#include <asm/sizes.h>
++#include <asm/io.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++#include <asm/mach/flash.h>
++
++#include <mach/mmc.h>
++#include <mach/udc.h>
++#include <mach/pxafb.h>
++#include <mach/ohci.h>
++#include <mach/pxa27x.h>
++#include <mach/pxa27x-udc.h>
++#include <mach/gpio.h>
++
++#include <mach/gumstix.h>
++
++#include "generic.h"
++
++#include <linux/delay.h>
++
++static struct resource flash_resource = {
++	.start	= 0x00000000,
++	.end	= SZ_64M - 1,
++	.flags	= IORESOURCE_MEM,
++};
++
++static struct mtd_partition gumstix_partitions[] = {
++	{
++		.name =		"u-boot",
++		.size =		0x00040000,
++		.offset =	0,
++		.mask_flags =	MTD_WRITEABLE  /* force read-only */
++	} , {
++		.name =		"rootfs",
++		.size =		0x01ec0000,
++		.offset =	0x00040000
++	} , {
++		.name =		"kernel",
++		.size =		0x00100000,
++		.offset =	0x01f00000
++	}
++};
++
++static struct flash_platform_data gumstix_flash_data = {
++	.map_name	= "cfi_probe",
++	.parts		= gumstix_partitions,
++	.nr_parts	= ARRAY_SIZE(gumstix_partitions),
++	.width		= 2,
++};
++
++static struct platform_device gumstix_flash_device = {
++	.name		= "pxa2xx-flash",
++	.id		= 0,
++	.dev = {
++		.platform_data = &gumstix_flash_data,
++	},
++	.resource = &flash_resource,
++	.num_resources = 1,
++};
++
++#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) \
++    || defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE)
++
++#include <linux/smsc911x.h>
++
++static struct resource verdex_smsc911x_resources[] = {
++	[0] = {
++		.name	= "smsc911x-memory",
++		.start  = PXA_CS1_PHYS,
++		.end    = PXA_CS1_PHYS + 0x000fffff,
++		.flags  = IORESOURCE_MEM,
++	},
++	[1] = {
++		.start  = PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_ETH0),
++		.end    = PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_ETH0),
++		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
++	},
++};
++
++static struct smsc911x_platform_config verdex_smsc911x_config = {
++	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
++	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
++	.flags		= SMSC911X_USE_16BIT | SMSC911X_SAVE_MAC_ADDRESS,
++	.phy_interface	= PHY_INTERFACE_MODE_MII,
++};
++
++static struct platform_device verdex_smsc911x_device = {
++	.name		= "smsc911x",
++	.id		= -1,
++	.num_resources	= ARRAY_SIZE(verdex_smsc911x_resources),
++	.resource	= verdex_smsc911x_resources,
++	.dev		= {
++		.platform_data = &verdex_smsc911x_config,
++	},
++};
++#endif
++
++#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
++static void __init verdex_init_smsc911x(void)
++{
++
++        printk(KERN_INFO "Initializing Gumstix verdex smsc911x\n");
++
++	if (gpio_request(GPIO_GUMSTIX_ETH0_RST, "SMSC911x_ETH0_RST") != 0) {
++		printk(KERN_ERR "could not obtain gpio for SMSC911x_ETH0_RST\n");
++		goto err_request_gpio_eth0_rst;
++	}
++
++	if (gpio_request(GPIO_GUMSTIX_ETH0, "SMSC911x_ETH0_IRQ") != 0) {
++		printk(KERN_ERR "could not obtain gpio for SMSC911x_ETH0_IRQ\n");
++		goto err_request_gpio_eth0_irq;
++	}
++
++	if (gpio_direction_output(GPIO_GUMSTIX_ETH0_RST, 0) != 0) {
++		printk(KERN_ERR "could not set SMSC911x_ETH0_RST pin to output\n");
++		goto err_dir;
++	}
++
++	gpio_set_value(GPIO_GUMSTIX_ETH0_RST, 0);
++
++	msleep(500); // Hold RESET for at least 200ms
++
++	gpio_set_value(GPIO_GUMSTIX_ETH0_RST, 1);
++
++	msleep(50);
++
++	if (gpio_direction_input(GPIO_GUMSTIX_ETH0) != 0) {
++		printk(KERN_ERR "could not set SMSC911x_ETH0_IRQ pin to input\n");
++		goto err_dir;
++	}
++
++	gpio_export(GPIO_GUMSTIX_ETH0, 0);
++	platform_device_register(&verdex_smsc911x_device);
++	return;
++
++err_dir:
++	gpio_free(GPIO_GUMSTIX_ETH0_RST);
++
++err_request_gpio_eth0_irq:
++	gpio_free(GPIO_GUMSTIX_ETH0);
++
++err_request_gpio_eth0_rst:
++	return;
++}
++
++#else
++static void __init verdex_init_smsc911x(void) { return; }
++#endif
++
++static unsigned long verdex_pin_config[] = {
++	/* MMC */
++	GPIO32_MMC_CLK,
++	GPIO112_MMC_CMD,
++	GPIO92_MMC_DAT_0,
++	GPIO109_MMC_DAT_1,
++	GPIO110_MMC_DAT_2,
++	GPIO111_MMC_DAT_3,
++
++	/* BTUART */
++	GPIO42_BTUART_RXD,
++	GPIO43_BTUART_TXD,
++	GPIO44_BTUART_CTS,
++	GPIO45_BTUART_RTS,
++
++	/* STUART */
++	GPIO46_STUART_RXD,
++	GPIO47_STUART_TXD,
++
++	/* FFUART */
++	GPIO34_FFUART_RXD,
++	GPIO39_FFUART_TXD,
++
++	/* SSP 2 */
++	GPIO19_SSP2_SCLK,
++	GPIO14_SSP2_SFRM,
++	GPIO13_SSP2_TXD,
++	GPIO11_SSP2_RXD,
++
++	/* SDRAM and local bus */
++	GPIO49_nPWE,
++	GPIO15_nCS_1,
++
++	/* I2C */
++	GPIO117_I2C_SCL,
++	GPIO118_I2C_SDA,
++
++	/* PWM 0 */
++	GPIO16_PWM0_OUT,
++
++	/* BRIGHTNESS */
++	GPIO17_PWM1_OUT,
++
++	/* LCD */
++	GPIO58_LCD_LDD_0,
++	GPIO59_LCD_LDD_1,
++	GPIO60_LCD_LDD_2,
++	GPIO61_LCD_LDD_3,
++	GPIO62_LCD_LDD_4,
++	GPIO63_LCD_LDD_5,
++	GPIO64_LCD_LDD_6,
++	GPIO65_LCD_LDD_7,
++	GPIO66_LCD_LDD_8,
++	GPIO67_LCD_LDD_9,
++	GPIO68_LCD_LDD_10,
++	GPIO69_LCD_LDD_11,
++	GPIO70_LCD_LDD_12,
++	GPIO71_LCD_LDD_13,
++	GPIO72_LCD_LDD_14,
++	GPIO73_LCD_LDD_15,
++	GPIO74_LCD_FCLK,
++	GPIO75_LCD_LCLK,
++	GPIO76_LCD_PCLK,
++#ifdef CONFIG_FB_PXA_SHARP_LQ043_PSP
++	/* DISP must be always high while screen is on */
++	/* Done below in verdex_init */
++#else
++	GPIO77_LCD_BIAS,
++#endif
++};
++
++#if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE)
++
++static unsigned long gpio_ntschg_0[] = {
++	GPIO104_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_nCD_0_MD);
++};
++
++static unsigned long gpio_ntschg_1[] = {
++	GPIO18_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_nSTSCHG_1_MD);
++	GPIO36_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_nCD_1_MD);
++	GPIO27_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_PRDY_nBSY_1_MD);
++};
++
++static unsigned long gpio_prdy_nbsy_old[] = {
++	GPIO111_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_nSTSCHG_0_MD);
++	GPIO109_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_PRDY_nBSY_0_OLD_MD);
++};
++
++static unsigned long gpio_prdy_nbsy[] = {
++	GPIO96_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_PRDY_nBSY_0_MD);
++};
++
++static unsigned long gpio_nhw_init[] = {
++	GPIO48_nPOE,			// pxa_gpio_mode(GPIO_GUMSTIX_nPOE_MD);
++	GPIO102_nPCE_1,			// pxa_gpio_mode(GPIO_GUMSTIX_nPCE_1_MD);
++	GPIO105_nPCE_2,			// pxa_gpio_mode(GPIO_GUMSTIX_nPCE_2_MD);
++	GPIO104_GPIO,			// pxa_gpio_mode(GPIO_GUMSTIX_nCD_0_MD);
++
++	GPIO49_nPWE,			// pxa_gpio_mode(GPIO_GUMSTIX_nPWE_MD);
++	GPIO50_nPIOR,			// pxa_gpio_mode(GPIO_GUMSTIX_nPIOR_MD);
++	GPIO51_nPIOW,			// pxa_gpio_mode(GPIO_GUMSTIX_nPIOW_MD);
++	GPIO79_PSKTSEL,			// pxa_gpio_mode(GPIO_GUMSTIX_pSKTSEL_MD);
++	GPIO55_nPREG,			// pxa_gpio_mode(GPIO_GUMSTIX_nPREG_MD);
++	GPIO56_nPWAIT,			// pxa_gpio_mode(GPIO_GUMSTIX_nPWAIT_MD);
++	GPIO57_nIOIS16,			// pxa_gpio_mode(GPIO_GUMSTIX_nIOIS16_MD);
++};
++
++static	int net_cf_vx_mode = 0;
++static	int pcmcia_cf_nr = 2;
++
++inline void __init gumstix_pcmcia_cpld_clk(void)
++{
++	GPCR(GPIO_GUMSTIX_nPOE) = GPIO_bit(GPIO_GUMSTIX_nPOE);
++	GPSR(GPIO_GUMSTIX_nPOE) = GPIO_bit(GPIO_GUMSTIX_nPOE);
++}
++
++inline unsigned char __init gumstix_pcmcia_cpld_read_bits(int bits)
++{
++	unsigned char result = 0;
++	unsigned int shift = 0;
++	while(bits--)
++	{
++		result |= !!(GPLR(GPIO_GUMSTIX_nCD_0) & GPIO_bit(GPIO_GUMSTIX_nCD_0)) << shift;
++		shift ++;
++		gumstix_pcmcia_cpld_clk();
++	}
++	printk("CPLD responded with: %02x\n",result);
++	return result;
++}
++
++/* We use the CPLD on the CF-CF card to read a value from a shift register.  If we can read that
++ * magic sequence, then we have 2 CF cards; otherwise we assume just one
++ * The CPLD will send the value of the shift register on GPIO11 (the CD line for slot 0)
++ * when RESET is held in reset.  We use GPIO48 (nPOE) as a clock signal,
++ * GPIO52/53 (card enable for both cards) to control read/write to the shift register
++ */
++static void __init gumstix_count_cards(void)
++{
++	if ((gpio_request(GPIO_GUMSTIX_nPOE, "GPIO_GUMSTIX_nPOE") == 0) &&
++	    (gpio_direction_output(GPIO_GUMSTIX_nPOE, 1) == 0))
++		gpio_export(GPIO_GUMSTIX_nPOE, 0);
++	else
++		printk(KERN_ERR "could not obtain gpio for GPIO_GUMSTIX_nPOE\n");
++
++	if ((gpio_request(GPIO_GUMSTIX_nPCE_1, "GPIO_GUMSTIX_nPCE_1") == 0) &&
++	    (gpio_direction_output(GPIO_GUMSTIX_nPCE_1, 1) == 0))
++		gpio_export(GPIO_GUMSTIX_nPCE_1, 0);
++	else
++		printk(KERN_ERR "could not obtain gpio for GPIO_GUMSTIX_nPCE_1\n");
++
++	if ((gpio_request(GPIO_GUMSTIX_nPCE_2, "GPIO_GUMSTIX_nPCE_2") == 0) &&
++	    (gpio_direction_output(GPIO_GUMSTIX_nPCE_2, 1) == 0))
++		gpio_export(GPIO_GUMSTIX_nPCE_2, 0);
++	else
++		printk(KERN_ERR "could not obtain gpio for GPIO_GUMSTIX_nPCE_2\n");
++
++	if ((gpio_request(GPIO_GUMSTIX_nCD_0, "GPIO_GUMSTIX_nCD_0") == 0) &&
++	    (gpio_direction_input(GPIO_GUMSTIX_nCD_0) == 0))
++		gpio_export(GPIO_GUMSTIX_nCD_0, 0);
++	else
++		printk(KERN_ERR "could not obtain gpio for GPIO_GUMSTIX_nCD_0\n");
++
++	if (net_cf_vx_mode) {
++		if ((gpio_request(GPIO_GUMSTIX_CF_OLD_RESET, "GPIO_GUMSTIX_CF_OLD_RESET") == 0) &&
++	    	    (gpio_direction_output(GPIO_GUMSTIX_CF_OLD_RESET, 1) == 0)) {
++			gpio_export(GPIO_GUMSTIX_CF_OLD_RESET, 0);
++		} else {
++			printk(KERN_ERR "could not obtain gpio for GPIO_GUMSTIX_CF_OLD_RESET\n");
++		}
++	} else {
++		if ((gpio_request(GPIO_GUMSTIX_CF_RESET, "GPIO_GUMSTIX_CF_RESET") == 0) &&
++	    	    (gpio_direction_output(GPIO_GUMSTIX_CF_RESET, 1) == 0)) {
++			gpio_export(GPIO_GUMSTIX_CF_RESET, 0);
++		} else {
++			printk(KERN_ERR "could not obtain gpio for GPIO_GUMSTIX_CF_RESET\n");
++		}
++	}
++
++	// Setup the shift register
++	GPSR(GPIO_GUMSTIX_nPCE_1) = GPIO_bit(GPIO_GUMSTIX_nPCE_1);
++	GPCR(GPIO_GUMSTIX_nPCE_2) = GPIO_bit(GPIO_GUMSTIX_nPCE_2);
++
++	// Tick the clock to program the shift register
++	gumstix_pcmcia_cpld_clk();
++
++	// Now set shift register into read mode
++	GPCR(GPIO_GUMSTIX_nPCE_1) = GPIO_bit(GPIO_GUMSTIX_nPCE_1);
++	GPSR(GPIO_GUMSTIX_nPCE_2) = GPIO_bit(GPIO_GUMSTIX_nPCE_2);
++
++	// We can read the bits now -- 0xC2 means "Dual compact flash"
++	if(gumstix_pcmcia_cpld_read_bits(8) != 0xC2)
++	{
++		// We do not have 2 CF slots
++		pcmcia_cf_nr = 1;
++	}
++
++	udelay(50);
++
++	if (net_cf_vx_mode) {
++		gpio_set_value(GPIO_GUMSTIX_CF_OLD_RESET, 0);
++		gpio_free(GPIO_GUMSTIX_CF_OLD_RESET);
++	} else {
++		gpio_set_value(GPIO_GUMSTIX_CF_RESET, 0);
++		gpio_free(GPIO_GUMSTIX_CF_RESET);
++	}
++
++	printk(KERN_INFO "found %d CF slots\n", pcmcia_cf_nr);
++
++	gpio_free(GPIO_GUMSTIX_nPCE_2);
++	gpio_free(GPIO_GUMSTIX_nPCE_1);
++	gpio_free(GPIO_GUMSTIX_nPOE);
++	return;
++}
++
++#define	SMC_IO_EXTENT	16
++#define	BANK_SELECT	14
++
++static void __init verdex_pcmcia_pin_config(void)
++{
++	struct resource *res;
++	void *network_controller_memory;
++	struct platform_device *pdev = &verdex_smsc911x_device;
++
++        printk(KERN_INFO "Initializing Gumstix verdex pcmcia\n");
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (res == NULL) {
++		printk(KERN_ERR "no memory resource defined\n");
++		goto err_done;
++	}
++
++	res = request_mem_region(res->start, SMC_IO_EXTENT, "smc91x probe");
++	if (res == NULL) {
++		printk(KERN_ERR "failed to request memory resource\n");
++		goto err_done;
++	}
++
++	// We check for the possibility of SMSC91c111 (reg base offset 0x300 from CS1 base)
++	network_controller_memory = ioremap(res->start + 0x300, SMC_IO_EXTENT);
++	if (network_controller_memory == NULL) {
++		printk(KERN_ERR "failed to ioremap() registers\n");
++		goto err_free_mem;
++	}
++
++	// Look for the special 91c111 value in the bank select register
++	if((0xff00 & readw(network_controller_memory+BANK_SELECT)) == 0x3300) {
++		printk(KERN_INFO "Detected netCF-vx board: pcmcia using older GPIO configuration\n");
++		net_cf_vx_mode = 1;
++	} else {
++		printk(KERN_INFO "Not netCF-vx board: pcmcia using newer GPIO configuration\n");
++		net_cf_vx_mode = 0;
++	}
++
++	iounmap(network_controller_memory);
++err_free_mem:
++	release_mem_region(res->start, SMC_IO_EXTENT);
++err_done:
++
++	gumstix_count_cards();	// this can update pcmcia_cf_nr
++
++	// If pcmcia_cf_nr is 1 then we do not have 2 CF slots
++	// Note: logic sequence was altered from previous kernel revs
++	// so that this works as intended now.
++	if (pcmcia_cf_nr != 0)
++	{
++		pxa2xx_mfp_config(ARRAY_AND_SIZE(gpio_ntschg_0));
++
++		if(net_cf_vx_mode)
++			pxa2xx_mfp_config(gpio_prdy_nbsy_old, 1);
++		else
++			pxa2xx_mfp_config(gpio_prdy_nbsy, 1);
++
++	} else {
++		// Note: this reconfigures pin GPIO18 to be GPIO-IN so make
++		// sure that this only gets done for the old dual slot board
++		// since that pin is an active AF1 out-mode signal (RDY) on
++		// newer boards and changing the pin mode on the newer boards
++		// would result in memory corruption for the NIC (and hang during
++		// PHY test).
++		pxa2xx_mfp_config(ARRAY_AND_SIZE(gpio_ntschg_1));
++	}
++
++	pxa2xx_mfp_config(ARRAY_AND_SIZE(gpio_nhw_init));
++	return;
++}
++
++int __init gumstix_get_cf_cards(void)
++{
++	return pcmcia_cf_nr;
++}
++EXPORT_SYMBOL(gumstix_get_cf_cards);
++
++#ifdef CONFIG_MACH_GUMSTIX_VERDEX
++int __init gumstix_check_if_netCF_vx(void)
++{
++	return net_cf_vx_mode;
++}
++EXPORT_SYMBOL(gumstix_check_if_netCF_vx);
++#endif
++
++#endif
++
++#if defined(CONFIG_FB_PXA_SHARP_LQ043_PSP) || defined(CONFIG_FB_PXA_SAMSUNG_LTE430WQ_F0C)
++static void gumstix_lcd_backlight(int on_or_off)
++{
++	int err;
++	err = gpio_request(17, "LCD BACKLIGHT");
++	if (err) {
++		//pr_warning("Gumstix Verdex: Failed to request LCD Backlight gpio\n");
++		return;
++	}
++
++	if(on_or_off) {
++		gpio_direction_input(17);
++	} else {
++		GPCR(17) = GPIO_bit(17);
++		gpio_direction_output(17, 0);
++		GPCR(17) = GPIO_bit(17);
++	}
++
++	return;
++}
++#endif
++
++#ifdef CONFIG_FB_PXA_ALPS_CDOLLAR
++static struct pxafb_mode_info gumstix_fb_mode = {
++	.pixclock	= 300000,
++	.xres		= 240,
++	.yres		= 320,
++	.bpp		= 16,
++	.hsync_len	= 2,
++	.left_margin	= 1,
++	.right_margin	= 1,
++	.vsync_len	= 3,
++	.upper_margin	= 0,
++	.lower_margin	= 0,
++	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
++};
++
++static struct pxafb_mach_info gumstix_fb_info = {
++	.modes		= &gumstix_fb_mode,
++	.num_modes	= 1,
++	.lccr0		= LCCR0_Pas | LCCR0_Sngl | LCCR0_Color,
++	.lccr3		= LCCR3_PixFlEdg,
++};
++#elif defined(CONFIG_FB_PXA_SHARP_LQ043_PSP)
++static struct pxafb_mode_info gumstix_fb_mode = {
++	.pixclock	= 110000,
++	.xres		= 480,
++	.yres		= 272,
++	.bpp		= 16,
++	.hsync_len	= 41,
++	.left_margin	= 2,
++	.right_margin	= 2,
++	.vsync_len	= 10,
++	.upper_margin	= 2,
++	.lower_margin	= 2,
++	.sync		= 0, // Hsync and Vsync both active low
++};
++
++static struct pxafb_mach_info gumstix_fb_info = {
++	.modes			= &gumstix_fb_mode,
++	.num_modes		= 1,
++	.lccr0			= LCCR0_Act | LCCR0_Sngl | LCCR0_Color,
++	.lccr3			= LCCR3_OutEnH | LCCR3_PixFlEdg | (0 << 30),
++	.pxafb_backlight_power	= &gumstix_lcd_backlight,
++};
++#elif defined(CONFIG_FB_PXA_SAMSUNG_LTE430WQ_F0C)
++static struct pxafb_mode_info gumstix_fb_mode = {
++	.pixclock	= 108696, // 9.2MHz typical DOTCLK from datasheet
++	.xres		= 480,
++	.hsync_len	= 41, // HLW from datasheet: 41 typ
++	.left_margin	= 4, // HBP - HLW from datasheet: 45 - 41 = 4
++	.right_margin	= 8, // HFP from datasheet: 8 typ
++	.yres		= 272,
++	.vsync_len	= 10, // VLW from datasheet: 10 typ
++	.upper_margin	= 2, // VBP - VLW from datasheet: 12 - 10 = 2
++	.lower_margin	= 4, // VFP from datasheet: 4 typ
++	.bpp		= 16,
++	.sync		= 0, // Hsync and Vsync both active low
++};
++
++static struct pxafb_mach_info gumstix_fb_info = {
++	.modes			= &gumstix_fb_mode,
++	.num_modes		= 1,
++	.lccr0			= LCCR0_Act | LCCR0_Sngl | LCCR0_Color,
++	.lccr3			= LCCR3_OutEnH | LCCR3_PixFlEdg | (0 << 30),
++	.pxafb_backlight_power	= &gumstix_lcd_backlight,
++};
++#endif
++
++static struct platform_device verdex_audio_device = {
++    .name       = "pxa2xx-ac97",
++    .id         = -1,
++};
++
++static struct platform_device *devices[] __initdata = {
++	&gumstix_flash_device,
++	&verdex_audio_device,
++};
++
++/* PXA27x OHCI controller setup */
++#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
++static int ohci_verdex_init(struct device *dev)
++{
++	// Turn on port 2 in host mode
++	UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
++
++	/* See drivers/usb/host/ohci-pxa27x.c for further details but
++           ENABLE_PORT_ALL flag is equivalent to using this old sequence:
++	UHCHR = (UHCHR) &
++		~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE);
++	*/
++	return 0;
++}
++
++static struct pxaohci_platform_data verdex_ohci_platform_data = {
++	.port_mode	= PMM_PERPORT_MODE,
++	.flags		= ENABLE_PORT_ALL,
++	.init		= ohci_verdex_init,
++};
++
++static void __init verdex_ohci_init(void)
++{
++	pxa_set_ohci_info(&verdex_ohci_platform_data);
++}
++#else
++static void __init verdex_ohci_init(void) {
++    printk(KERN_INFO "Gumstix verdex host usb ohci is disabled\n");
++}
++#endif
++
++
++#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
++static struct pxamci_platform_data verdex_mci_platform_data;
++
++static int verdex_mci_init(struct device *dev, irq_handler_t detect_int,
++                void *data)
++{
++	/* GPIO setup for MMC on the 120-pin connector is done in verdex_init.
++	 * There is no card detect on a uSD connector so no interrupt to
++	 * register. There is no WP detect GPIO line either.
++	 */
++
++	return 0;
++}
++
++static struct pxamci_platform_data verdex_mci_platform_data = {
++	.ocr_mask   = MMC_VDD_32_33|MMC_VDD_33_34,
++	.init       = verdex_mci_init,
++	.gpio_card_detect 	= -1,
++	.gpio_card_ro		= -1,
++	.gpio_power		= -1,
++};
++
++static void __init verdex_mmc_init(void)
++{
++	pxa_set_mci_info(&verdex_mci_platform_data);
++}
++#else
++static void __init verdex_mmc_init(void)
++{
++	printk(KERN_INFO "Gumstix verdex mmc disabled\n");
++}
++#endif
++
++#if defined(CONFIG_USB_GADGET_PXA2XX) || defined(CONFIG_USB_GADGET_PXA2XX_MODULE)
++static struct pxa2xx_udc_mach_info verdex_udc_info __initdata = {
++	.gpio_vbus	= GPIO35,
++	.gpio_pullup	= GPIO41,
++};
++
++static void __init verdex_udc_init(void)
++{
++	pxa_set_udc_info(&verdex_udc_info);
++}
++#else
++static void __init verdex_udc_init(void)
++{
++	printk(KERN_INFO "Gumstix verdex udc is disabled\n");
++}
++#endif
++
++#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
++
++#if defined(CONFIG_TOUCHSCREEN_TSC2003) || defined(CONFIG_TOUCHSCREEN_TSC2003_MODULE)
++
++#define VERDEX_GPIO_PENDOWN	16
++
++static int tsc2003_init_platform_hw(void)
++{
++	return 0;
++}
++
++static void tsc2003_exit_platform_hw(void)
++{
++	return;
++}
++
++static void tsc2003_clear_penirq(void)
++{
++	return;
++}
++
++static int tsc2003_get_pendown_state(void)
++{
++	return !gpio_get_value(VERDEX_GPIO_PENDOWN);
++}
++
++static struct tsc2007_platform_data tsc2003_config = {
++	.model			= 2003,
++	.x_plate_ohms		= 100,
++	.get_pendown_state	= tsc2003_get_pendown_state,
++	.clear_penirq		= tsc2003_clear_penirq,
++	.init_platform_hw	= tsc2003_init_platform_hw,
++	.exit_platform_hw	= tsc2003_exit_platform_hw,
++};
++#endif
++
++static struct i2c_board_info __initdata verdex_i2c_board_info[] = {
++#if defined(CONFIG_RTC_DRV_DS1307) || defined(CONFIG_RTC_DRV_DS1307_MODULE)
++	{
++		I2C_BOARD_INFO("rtc-ds1307", 0x68),
++	},
++#endif
++#if defined(CONFIG_TOUCHSCREEN_TSC2003) || defined(CONFIG_TOUCHSCREEN_TSC2003_MODULE)
++	{
++		I2C_BOARD_INFO("tsc2003", 0x48),
++		.platform_data	= &tsc2003_config,
++		.irq		= IRQ_GPIO(VERDEX_GPIO_PENDOWN),
++	},
++#endif
++};
++
++static struct i2c_pxa_platform_data verdex_i2c_pwr_info = {
++	.fast_mode = 1,
++};
++
++static struct i2c_pxa_platform_data verdex_i2c_info = {
++	.fast_mode = 1,
++};
++
++static void __init verdex_i2c_init(void)
++{
++	printk(KERN_INFO "Initializing Gumstix verdex i2c\n");
++
++#if defined(CONFIG_TOUCHSCREEN_TSC2003) || defined(CONFIG_TOUCHSCREEN_TSC2003_MODULE)
++	if ((gpio_request(VERDEX_GPIO_PENDOWN, "TSC2003_PENDOWN") == 0) &&
++	    (gpio_direction_input(VERDEX_GPIO_PENDOWN) == 0)) {
++		gpio_export(VERDEX_GPIO_PENDOWN, 0);
++	} else {
++		printk(KERN_ERR "could not obtain gpio for TSC2003_PENDOWN\n");
++		return;
++	}
++#endif
++
++	i2c_register_board_info(0, verdex_i2c_board_info,
++				ARRAY_SIZE(verdex_i2c_board_info));
++	pxa_set_i2c_info(&verdex_i2c_info);
++	pxa27x_set_i2c_power_info(&verdex_i2c_pwr_info);
++}
++#else
++static inline void verdex_i2c_init(void) {}
++#endif
++
++#if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE)
++static void __init verdex_pcmcia_init(void)
++{
++	verdex_pcmcia_pin_config();
++}
++#else
++static void __init verdex_pcmcia_init(void) {
++	printk(KERN_INFO "Gumstix verdex pcmcia is disabled\n");
++}
++#endif
++
++
++static void __init verdex_init(void)
++{
++	pxa2xx_mfp_config(ARRAY_AND_SIZE(verdex_pin_config));
++
++#ifdef CONFIG_FB_PXA_SHARP_LQ043_PSP
++	/* DISP must be always high while screen is on */
++	gpio_direction_output(GPIO77, 0);
++	GPSR(GPIO77) = GPIO_bit(GPIO77);
++#endif
++	verdex_udc_init();
++	verdex_mmc_init();
++	verdex_ohci_init();
++	verdex_i2c_init();
++	verdex_init_smsc911x();
++	verdex_pcmcia_init();
++
++#if defined(CONFIG_FB_PXA_ALPS_CDOLLAR) || defined(CONFIG_FB_PXA_SHARP_LQ043_PSP) || defined(CONFIG_FB_PXA_SAMSUNG_LTE430WQ_F0C)
++	printk(KERN_INFO "Initializing Gumstix verdex FB info\n");
++	set_pxa_fb_info(&gumstix_fb_info);
++#endif
++	printk(KERN_INFO "Initializing Gumstix platform_add_devices\n");
++	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
++}
++
++MACHINE_START(GUMSTIX, "Gumstix verdex")
++	.atag_offset    = 0x100, /* match u-boot bi_boot_params */
++	.map_io         = pxa27x_map_io,
++	.init_irq       = pxa27x_init_irq,
++	.handle_irq	= pxa27x_handle_irq,
++	.timer          = &pxa_timer,
++	.init_machine   = verdex_init,
++	.restart	= pxa_restart,
++MACHINE_END
+--- a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
++++ b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
+@@ -109,6 +109,7 @@
+ #define GPIO54_nPCE_2		MFP_CFG_OUT(GPIO54, AF2, DRIVE_HIGH)
+ #define GPIO78_nPCE_2		MFP_CFG_OUT(GPIO78, AF1, DRIVE_HIGH)
+ #define GPIO87_nPCE_2		MFP_CFG_IN(GPIO87, AF1)
++#define GPIO105_nPCE_2		MFP_CFG_OUT(GPIO105, AF1, DRIVE_HIGH)
+ #define GPIO55_nPREG		MFP_CFG_OUT(GPIO55, AF2, DRIVE_HIGH)
+ #define GPIO50_nPIOR		MFP_CFG_OUT(GPIO50, AF2, DRIVE_HIGH)
+ #define GPIO51_nPIOW		MFP_CFG_OUT(GPIO51, AF2, DRIVE_HIGH)

target/linux/pxa/patches-3.3/002-verdex_lcd_support.patch

@@ -0,0 +1,52 @@
+From eb92a178eceae4e5d18bbb442b8e44cb88457d60 Mon Sep 17 00:00:00 2001
+From: Joseph Kortje <jpktech@rogers.com>
+Date: Wed, 28 Oct 2009 21:25:57 -0400
+Subject: [PATCH] [ARM] Gumstix Verdex LCD config options
+
+add options to Kconfig for Verdex LCD support
+
+Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
+---
+ drivers/video/Kconfig |   31 +++++++++++++++++++++++++++++++
+ 1 files changed, 31 insertions(+), 0 deletions(-)
+
+--- a/drivers/video/Kconfig
++++ b/drivers/video/Kconfig
+@@ -1892,6 +1892,37 @@ config FB_PXA
+ 	  say M here and read <file:Documentation/kbuild/modules.txt>.
+ 
+ 	  If unsure, say N.
++choice
++	depends on FB_PXA
++	prompt "LCD Panel"
++	default FB_PXA_SAMSUNG_LTE430WQ_F0C
++
++config FB_PXA_ALPS_CDOLLAR
++	boolean "Chris Dollar's ALPS screen"
++	---help---
++	  Enable definitions (over-ridable on the kernel command line if
++	  "PXA LCD command line parameters" is also selected) for an ALPS
++	  screen which Chris Dollar uses
++
++config FB_PXA_SHARP_LQ043_PSP
++	boolean "SHARP LQ043... series"
++	---help---
++	  Enable definitions (over-ridable on the kernel command line if
++	  "PXA LCD command line parameters" is also selected) for a SHARP
++	  LQ043... screen, such as the one used by the PSP.  These screens are
++	  the ones normally sold by gumstix with its boards.
++
++config FB_PXA_SAMSUNG_LTE430WQ_F0C
++	boolean "Samsung LTE430WQ-F0C (standard gumstix LCD)"
++	---help---
++	  Enable definitions for a Samsung LTE430WQ-F0C LCD panel, such as the ones resold
++	  by gumstix for use with their "LCD-Ready" boards.
++
++config FB_PXA_NONEOFTHEABOVE
++	boolean "None of the above"
++
++endchoice
++
+ 
+ config FB_PXA_OVERLAY
+ 	bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"

target/linux/pxa/patches-3.3/003-gumstix_h_verdex_pro_support.patch

@@ -0,0 +1,209 @@
+From adb6abbe4e3bc17c20cdc70e4a4357f1633d4970 Mon Sep 17 00:00:00 2001
+From: Joseph Kortje <jpktech@rogers.com>
+Date: Wed, 28 Oct 2009 21:49:11 -0400
+Subject: [PATCH] [ARM] gumstix.h: Verdex Pro support
+
+Added a bunch of ifdefs to support both original gumstix boards
+as well as the Verdex Pro in gumstix.h
+
+Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
+---
+ arch/arm/mach-pxa/include/mach/gumstix.h |  160 ++++++++++++++++++++++++------
+ 1 files changed, 130 insertions(+), 30 deletions(-)
+
+--- a/arch/arm/mach-pxa/include/mach/gumstix.h
++++ b/arch/arm/mach-pxa/include/mach/gumstix.h
+@@ -6,6 +6,9 @@
+  * published by the Free Software Foundation.
+  */
+ 
++#if !defined(__ASM_ARCH_MFP_PXA27X_H) && !defined(__ASM_ARCH_MFP_PXA25X_H)
++	#error You need to include either mfp-pxa27x.h or mfp-pxa25x.h
++#endif
+ 
+ /* BTRESET - Reset line to Bluetooth module, active low signal. */
+ #define GPIO_GUMSTIX_BTRESET          7
+@@ -20,9 +23,18 @@ this moves to GPIO17 and GPIO37. */
+ /* GPIOx - Connects to USB D+ and used as a pull-up after GPIOn
+ has detected a cable insertion; driven low otherwise. */
+ 
++#ifndef CONFIG_MACH_GUMSTIX_VERDEX
++
+ #define GPIO_GUMSTIX_USB_GPIOn		35
+ #define GPIO_GUMSTIX_USB_GPIOx		41
+ 
++#else
++
++#define GPIO_GUMSTIX_USB_GPIOn         100
++#define GPIO_GUMSTIX_USB_GPIOx         27
++
++#endif
++
+ /* usb state change */
+ #define GUMSTIX_USB_INTR_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_USB_GPIOn)
+ 
+@@ -42,48 +54,135 @@ has detected a cable insertion; driven l
+  * ETH_RST provides a hardware reset line to the ethernet chip
+  * ETH is the IRQ line in from the ethernet chip to the PXA
+  */
++#ifndef CONFIG_MACH_GUMSTIX_VERDEX
+ #define GPIO_GUMSTIX_ETH0_RST		80
+-#define GPIO_GUMSTIX_ETH0_RST_MD	(GPIO_GUMSTIX_ETH0_RST | GPIO_OUT)
++#define GPIO_GUMSTIX_ETH0		36
++#else
++#define GPIO_GUMSTIX_ETH0_RST		107
++#define GPIO_GUMSTIX_ETH0		99
++#endif
+ #define GPIO_GUMSTIX_ETH1_RST		52
+-#define GPIO_GUMSTIX_ETH1_RST_MD	(GPIO_GUMSTIX_ETH1_RST | GPIO_OUT)
++#define GPIO_GUMSTIX_ETH1		27
+ 
+-#define GPIO_GUMSTIX_ETH0		36
++#define GPIO_GUMSTIX_ETH0_RST_MD	(GPIO_GUMSTIX_ETH0_RST | GPIO_OUT)
++#define GPIO_GUMSTIX_ETH1_RST_MD	(GPIO_GUMSTIX_ETH1_RST | GPIO_OUT)
+ #define GPIO_GUMSTIX_ETH0_MD		(GPIO_GUMSTIX_ETH0 | GPIO_IN)
+-#define GUMSTIX_ETH0_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_ETH0)
+-#define GPIO_GUMSTIX_ETH1		27
+ #define GPIO_GUMSTIX_ETH1_MD		(GPIO_GUMSTIX_ETH1 | GPIO_IN)
+-#define GUMSTIX_ETH1_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_ETH1)
+ 
++#define GUMSTIX_ETH0_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_ETH0)
++#define GUMSTIX_ETH1_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_ETH1)
+ 
+-/* CF reset line */
+-#define GPIO8_RESET			8
+-
+-/* CF slot 0 */
+-#define GPIO4_nBVD1			4
+-#define GPIO4_nSTSCHG			GPIO4_nBVD1
+-#define GPIO11_nCD			11
+-#define GPIO26_PRDY_nBSY		26
+-#define GUMSTIX_S0_nSTSCHG_IRQ		PXA_GPIO_TO_IRQ(GPIO4_nSTSCHG)
+-#define GUMSTIX_S0_nCD_IRQ		PXA_GPIO_TO_IRQ(GPIO11_nCD)
+-#define GUMSTIX_S0_PRDY_nBSY_IRQ	PXA_GPIO_TO_IRQ(GPIO26_PRDY_nBSY)
++ /* CF reset line */
++#define GPIO8_CF_RESET			8
++#define GPIO97_CF_RESET			97
++#define GPIO110_CF_RESET		110
++
++#ifndef CONFIG_MACH_GUMSTIX_VERDEX
++#define GPIO_GUMSTIX_CF_RESET		GPIO8_CF_RESET
++#else
++#define GPIO_GUMSTIX_CF_RESET		GPIO97_CF_RESET
++#endif
++
++#define GPIO_GUMSTIX_CF_OLD_RESET	GPIO110_CF_RESET
++
++/* CF signals shared by both sockets */
++#define GPIO_GUMSTIX_nPOE	48
++#define GPIO_GUMSTIX_nPWE	49
++#define GPIO_GUMSTIX_nPIOR	50
++#define GPIO_GUMSTIX_nPIOW	51
++
++#ifndef CONFIG_MACH_GUMSTIX_VERDEX
++#define GPIO_GUMSTIX_nPCE_1	52
++#define GPIO_GUMSTIX_nPCE_2	53
++#define GPIO_GUMSTIX_pSKTSEL	54
++#else
++#define GPIO_GUMSTIX_nPCE_1	102
++#define GPIO_GUMSTIX_nPCE_2	105
++#define GPIO_GUMSTIX_pSKTSEL	79
++#endif
++
++#define GPIO_GUMSTIX_nPREG	55
++#define GPIO_GUMSTIX_nPWAIT	56
++#define GPIO_GUMSTIX_nIOIS16	57
++
++/* Pin mode definitions correspond to mfp-pxa2[57]x.h */
++#define GPIO_GUMSTIX_nPOE_MD	GPIO48_nPOE
++#define GPIO_GUMSTIX_nPWE_MD	GPIO49_nPWE
++#define GPIO_GUMSTIX_nPIOR_MD	GPIO50_nPIOR
++#define GPIO_GUMSTIX_nPIOW_MD	GPIO51_nPIOW
++
++#ifndef CONFIG_MACH_GUMSTIX_VERDEX
++#define GPIO_GUMSTIX_nPCE_1_MD	GPIO52_nPCE_1
++#define GPIO_GUMSTIX_nPCE_2_MD	GPIO53_nPCE_2
++#define GPIO_GUMSTIX_pSKTSEL_MD	GPIO54_pSKTSEL
++#else
++#define GPIO_GUMSTIX_nPCE_1_MD	GPIO102_nPCE_1
++#define GPIO_GUMSTIX_nPCE_2_MD	GPIO105_nPCE_2
++#define GPIO_GUMSTIX_pSKTSEL_MD	GPIO79_pSKTSEL
++#endif
++
++#define GPIO_GUMSTIX_nPREG_MD	GPIO55_nPREG
++#define GPIO_GUMSTIX_nPWAIT_MD	GPIO56_nPWAIT
++#define GPIO_GUMSTIX_nIOIS16_MD	GPIO57_nIOIS16
++
++ /* CF slot 0 */
++#define GPIO4_nBVD1_0			4
++#define GPIO4_nSTSCHG_0			GPIO4_nBVD1_0
++#define GPIO11_nCD_0			11
++#define GPIO26_PRDY_nBSY_0		26
++
++#define GPIO111_nBVD1_0			111
++#define GPIO111_nSTSCHG_0		GPIO111_nBVD1_0
++#define GPIO104_nCD_0			104
++#define GPIO96_PRDY_nBSY_0		96
++#define GPIO109_PRDY_nBSY_0		109
++
++#ifndef CONFIG_MACH_GUMSTIX_VERDEX
++#define GPIO_GUMSTIX_nBVD1_0		GPIO4_nBVD1_0
++#define GPIO_GUMSTIX_nSTSCHG_0		GPIO4_nSTSCHG_0
++#define GPIO_GUMSTIX_nCD_0		GPIO11_nCD_0
++#define GPIO_GUMSTIX_PRDY_nBSY_0	GPIO26_PRDY_nBSY_0
++#else
++#define GPIO_GUMSTIX_nBVD1_0		GPIO111_nBVD1_0
++#define GPIO_GUMSTIX_nSTSCHG_0		GPIO111_nSTSCHG_0
++#define GPIO_GUMSTIX_nCD_0		GPIO104_nCD_0
++#define GPIO_GUMSTIX_PRDY_nBSY_0	GPIO96_PRDY_nBSY_0
++#endif
++
++#define GPIO_GUMSTIX_PRDY_nBSY_0_OLD	GPIO109_PRDY_nBSY_0
++
++#define GUMSTIX_S0_nSTSCHG_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_nSTSCHG_0)
++#define GUMSTIX_S0_nCD_IRQ		PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_nCD_0)
++#define GUMSTIX_S0_PRDY_nBSY_IRQ	PXA_GPIO_TO_IRQ(GPIO_GUMSTIX_PRDY_nBSY_0)
+ 
+ /* CF slot 1 */
+-#define GPIO18_nBVD1			18
+-#define GPIO18_nSTSCHG			GPIO18_nBVD1
+-#define GPIO36_nCD			36
+-#define GPIO27_PRDY_nBSY		27
++#define GPIO18_nBVD1_1			18
++#define GPIO18_nSTSCHG_1		GPIO18_nBVD1_1
++#define GPIO36_nCD_1			36
++#define GPIO27_PRDY_nBSY_1		27
++
++#define GPIO_GUMSTIX_nBVD1_1		GPIO18_nBVD1_1
++#define GPIO_GUMSTIX_nSTSCHG_1		GPIO18_nSTSCHG_1
++#define GPIO_GUMSTIX_nCD_1		GPIO36_nCD_1
++#define GPIO_GUMSTIX_PRDY_nBSY_1	GPIO27_PRDY_nBSY_1
++
+ #define GUMSTIX_S1_nSTSCHG_IRQ		PXA_GPIO_TO_IRQ(GPIO18_nSTSCHG)
+ #define GUMSTIX_S1_nCD_IRQ		PXA_GPIO_TO_IRQ(GPIO36_nCD)
+ #define GUMSTIX_S1_PRDY_nBSY_IRQ	PXA_GPIO_TO_IRQ(GPIO27_PRDY_nBSY)
+ 
+-/* CF GPIO line modes */
+-#define GPIO4_nSTSCHG_MD		(GPIO4_nSTSCHG | GPIO_IN)
+-#define GPIO8_RESET_MD			(GPIO8_RESET | GPIO_OUT)
+-#define GPIO11_nCD_MD			(GPIO11_nCD | GPIO_IN)
+-#define GPIO18_nSTSCHG_MD		(GPIO18_nSTSCHG | GPIO_IN)
+-#define GPIO26_PRDY_nBSY_MD		(GPIO26_PRDY_nBSY | GPIO_IN)
+-#define GPIO27_PRDY_nBSY_MD		(GPIO27_PRDY_nBSY | GPIO_IN)
+-#define GPIO36_nCD_MD			(GPIO36_nCD | GPIO_IN)
++/* CF GPIO line modes - correspond to mfp-pxa2[57]x.h */
++#define GPIO_GUMSTIX_CF_RESET_MD	(GPIO_GUMSTIX_CF_RESET | GPIO_OUT)
++#define GPIO_GUMSTIX_CF_OLD_RESET_MD	(GPIO_GUMSTIX_CF_OLD_RESET | GPIO_OUT)
++
++#define GPIO_GUMSTIX_nSTSCHG_0_MD	GPIO111_GPIO
++#define GPIO_GUMSTIX_nCD_0_MD		GPIO104_GPIO
++
++#define GPIO_GUMSTIX_PRDY_nBSY_0_MD	GPIO96_GPIO
++#define GPIO_GUMSTIX_PRDY_nBSY_0_OLD_MD	GPIO109_GPIO
++
++#define GPIO_GUMSTIX_nSTSCHG_1_MD	GPIO18_GPIO
++#define GPIO_GUMSTIX_nCD_1_MD		GPIO36_GPIO
++#define GPIO_GUMSTIX_PRDY_nBSY_1_MD	GPIO27_GPIO
+ 
+ /* for expansion boards that can't be programatically detected */
+ extern int am200_init(void);

target/linux/pxa/patches-3.3/004-smsc911x_verdex_pro_support.patch

@@ -0,0 +1,100 @@
+From 7645a459feb02f7aae4c3a5724b7800495d1b659 Mon Sep 17 00:00:00 2001
+From: Bobby Powers <bobbypowers@gmail.com>
+Date: Wed, 28 Oct 2009 22:41:31 -0400
+Subject: [PATCH] [ARM] smsc911x: Verdex Pro support
+
+Basically Joseph Kortje's patch, cleaned up to apply to Linus's
+tree.  Some of the smsc911x.c had been applied already
+
+Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
+---
+ drivers/net/smsc911x.c   |   50 +++++++++++++++++++++++++++++++++++++--------
+ drivers/net/smsc911x.h   |    2 +-
+ include/linux/smsc911x.h |   11 ++++++++++
+ 3 files changed, 53 insertions(+), 10 deletions(-)
+
+--- a/drivers/net/ethernet/smsc/smsc911x.c
++++ b/drivers/net/ethernet/smsc/smsc911x.c
+@@ -1485,7 +1485,7 @@ static int smsc911x_open(struct net_devi
+ 		SMSC_WARN(pdata, ifup,
+ 			  "Timed out waiting for EEPROM busy bit to clear");
+ 
+-	smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000);
++ 	smsc911x_reg_write(pdata, GPIO_CFG, GPIO_CFG_LED1_EN_ | GPIO_CFG_LED2_EN_ | (1 << 20));
+ 
+ 	/* The soft reset above cleared the device's MAC address,
+ 	 * restore it from local copy (set in probe) */
+@@ -1497,8 +1497,8 @@ static int smsc911x_open(struct net_devi
+ 	smsc911x_reg_write(pdata, INT_EN, 0);
+ 	smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF);
+ 
+-	/* Set interrupt deassertion to 100uS */
+-	intcfg = ((10 << 24) | INT_CFG_IRQ_EN_);
++ 	/* Set interrupt deassertion to 22*10uS */
++ 	intcfg = ((22 << 24) | INT_CFG_IRQ_EN_);
+ 
+ 	if (pdata->config.irq_polarity) {
+ 		SMSC_TRACE(pdata, ifup, "irq polarity: active high");
+@@ -1524,7 +1524,7 @@ static int smsc911x_open(struct net_devi
+ 	temp |= INT_EN_SW_INT_EN_;
+ 	smsc911x_reg_write(pdata, INT_EN, temp);
+ 
+-	timeout = 1000;
++	timeout = 2000;
+ 	while (timeout--) {
+ 		if (pdata->software_irq_signal)
+ 			break;
+@@ -2332,6 +2332,38 @@ static inline int smsc911x_probe_config_
+ }
+ #endif /* CONFIG_OF */
+ 
++static inline unsigned int is_gumstix_oui(u8 *addr)
++{
++	return (addr[0] == 0x00 && addr[1] == 0x15 && addr[2] == 0xC9);
++}
++
++/**
++ * gen_serial_ether_addr - Generate software assigned Ethernet address
++ * based on the system_serial number
++ * @addr: Pointer to a six-byte array containing the Ethernet address
++ *
++ * Generate an Ethernet address (MAC) that is not multicast
++ * and has the local assigned bit set, keyed on the system_serial
++ */
++static inline void gen_serial_ether_addr(u8 *addr)
++{
++	static u8 ether_serial_digit = 0;
++	addr [0] = system_serial_high >> 8;
++	addr [1] = system_serial_high;
++	addr [2] = system_serial_low >> 24;
++	addr [3] = system_serial_low >> 16;
++	addr [4] = system_serial_low >> 8;
++	addr [5] = (system_serial_low & 0xc0) |	/* top bits are from system serial */
++		(1 << 4) |			/* 2 bits identify interface type 1=ether, 2=usb, 3&4 undef */
++		((ether_serial_digit++) & 0x0f);	/* 15 possible interfaces of each type */
++
++	if(!is_gumstix_oui(addr))
++	{
++		addr [0] &= 0xfe;		/* clear multicast bit */
++		addr [0] |= 0x02;		/* set local assignment bit (IEEE802) */
++	}
++}
++
+ static int __devinit smsc911x_drv_probe(struct platform_device *pdev)
+ {
+ 	struct device_node *np = pdev->dev.of_node;
+@@ -2481,11 +2513,11 @@ static int __devinit smsc911x_drv_probe(
+ 			SMSC_TRACE(pdata, probe,
+ 				   "Mac Address is read from LAN911x EEPROM");
+ 		} else {
+-			/* eeprom values are invalid, generate random MAC */
+-			random_ether_addr(dev->dev_addr);
++			/* eeprom values are invalid, generate MAC from serial number */
++			gen_serial_ether_addr(dev->dev_addr);
+ 			smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
+ 			SMSC_TRACE(pdata, probe,
+-				   "MAC Address is set to random_ether_addr");
++				"MAC Address is derived from system serial number");
+ 		}
+ 	}
+ 

target/linux/pxa/patches-3.3/005-verdex_pcmcia_support.patch

@@ -0,0 +1,235 @@
+From 76a102bd5c9d792db19c6c72eafdecea0311a0c9 Mon Sep 17 00:00:00 2001
+From: Craig Hughes <craig@gumstix.com>
+Date: Fri, 30 Oct 2009 14:16:27 -0400
+Subject: [PATCH] [ARM] pxa: Gumstix Verdex PCMCIA support
+
+Needed for the Libertas CS wireless device.
+
+Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
+---
+ drivers/pcmcia/Kconfig          |    3 +-
+ drivers/pcmcia/Makefile         |    3 +
+ drivers/pcmcia/pxa2xx_gumstix.c |  194 +++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 199 insertions(+), 1 deletions(-)
+ create mode 100644 drivers/pcmcia/pxa2xx_gumstix.c
+
+--- a/drivers/pcmcia/Kconfig
++++ b/drivers/pcmcia/Kconfig
+@@ -212,7 +212,7 @@ config PCMCIA_PXA2XX
+ 		    || MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \
+ 		    || ARCOM_PCMCIA || ARCH_PXA_ESERIES || MACH_STARGATE2 \
+ 		    || MACH_VPAC270 || MACH_BALLOON3 || MACH_COLIBRI \
+-		    || MACH_COLIBRI320)
++		    || MACH_COLIBRI320 || ARCH_GUMSTIX)
+ 	select PCMCIA_SOC_COMMON
+ 	help
+ 	  Say Y here to include support for the PXA2xx PCMCIA controller
+--- a/drivers/pcmcia/Makefile
++++ b/drivers/pcmcia/Makefile
+@@ -70,6 +70,9 @@ pxa2xx-obj-$(CONFIG_MACH_BALLOON3)		+= p
+ pxa2xx-obj-$(CONFIG_MACH_COLIBRI)		+= pxa2xx_colibri.o
+ pxa2xx-obj-$(CONFIG_MACH_COLIBRI320)		+= pxa2xx_colibri.o
+ 
++pxa2xx-obj-$(CONFIG_MACH_GUMSTIX_VERDEX)	+= pxa2xx_cs.o
++pxa2xx_cs-objs					:= pxa2xx_gumstix.o
++
+ obj-$(CONFIG_PCMCIA_PXA2XX)			+= pxa2xx_base.o $(pxa2xx-obj-y)
+ 
+ obj-$(CONFIG_PCMCIA_XXS1500)			+= xxs1500_ss.o
+--- /dev/null
++++ b/drivers/pcmcia/pxa2xx_gumstix.c
+@@ -0,0 +1,194 @@
++/*
++ * linux/drivers/pcmcia/pxa2xx_gumstix.c
++ *
++ * Gumstix PCMCIA specific routines. Based on Mainstone
++ *
++ * Copyright 2004, Craig Hughes <craig@gumstix.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++
++#include <linux/module.h>
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/errno.h>
++#include <linux/interrupt.h>
++#include <linux/irq.h>
++#include <linux/gpio.h>
++
++#include <linux/delay.h>
++#include <linux/platform_device.h>
++
++#include <pcmcia/ss.h>
++
++#include <mach/hardware.h>
++#include <asm/mach-types.h>
++
++#ifdef CONFIG_MACH_GUMSTIX_VERDEX
++#include <mach/pxa27x.h>
++#else
++#include <mach/pxa27x.h>
++#endif
++
++#include <asm/io.h>
++#include <mach/gpio.h>
++#include <mach/gumstix.h>
++#include "soc_common.h"
++
++#define ARRAY_AND_SIZE(x)	(x), ARRAY_SIZE(x)
++
++static struct pcmcia_irqs gumstix_pcmcia_irqs0[] = {
++	{ 0, GUMSTIX_S0_nCD_IRQ,	"CF0 nCD"     },
++	{ 0, GUMSTIX_S0_nSTSCHG_IRQ,	"CF0 nSTSCHG" },
++};
++
++static struct pcmcia_irqs gumstix_pcmcia_irqs1[] = {
++	{ 1, GUMSTIX_S1_nCD_IRQ,	"CF1 nCD"     },
++	{ 1, GUMSTIX_S1_nSTSCHG_IRQ,	"CF1 nSTSCHG" },
++};
++
++
++static int net_cf_vx_mode = 0;
++
++static int gumstix_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
++{
++/* Note: The verdex_pcmcia_pin_config is moved to gumstix_verdex.c in order to use mfp_pxa2xx_config
++   for board-specific pin configuration instead of the old deprecated pxa_gpio_mode function.  Thus,
++   only the IRQ init is still needed to be done here. */
++	skt->irq = (skt->nr == 0) ? ((net_cf_vx_mode == 0) ? GUMSTIX_S0_PRDY_nBSY_IRQ : GUMSTIX_S0_PRDY_nBSY_OLD_IRQ) : GUMSTIX_S1_PRDY_nBSY_IRQ;
++
++	return (skt->nr == 0) ? soc_pcmcia_request_irqs(skt, gumstix_pcmcia_irqs0, ARRAY_SIZE(gumstix_pcmcia_irqs0)) :
++				soc_pcmcia_request_irqs(skt, gumstix_pcmcia_irqs1, ARRAY_SIZE(gumstix_pcmcia_irqs1));
++}
++
++static void gumstix_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
++{
++	if(skt->nr == 0)
++	{
++		soc_pcmcia_free_irqs(skt, gumstix_pcmcia_irqs0, ARRAY_SIZE(gumstix_pcmcia_irqs0));
++	} else {
++		soc_pcmcia_free_irqs(skt, gumstix_pcmcia_irqs1, ARRAY_SIZE(gumstix_pcmcia_irqs1));
++	}
++
++	if (net_cf_vx_mode) {
++	    	gpio_free(GPIO_GUMSTIX_CF_OLD_RESET);
++	} else {
++		gpio_free(GPIO_GUMSTIX_CF_RESET);
++	}
++
++}
++
++static void gumstix_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
++				    struct pcmcia_state *state)
++{
++	unsigned int cd, prdy_nbsy, nbvd1;
++	if(skt->nr == 0)
++	{
++		cd = GPIO_GUMSTIX_nCD_0;
++		if(net_cf_vx_mode)
++			prdy_nbsy = GPIO_GUMSTIX_PRDY_nBSY_0_OLD;
++		else
++			prdy_nbsy = GPIO_GUMSTIX_PRDY_nBSY_0;
++		nbvd1 = GPIO_GUMSTIX_nBVD1_0;
++	} else {
++		cd = GPIO_GUMSTIX_nCD_1;
++		prdy_nbsy = GPIO_GUMSTIX_PRDY_nBSY_1;
++		nbvd1 = GPIO_GUMSTIX_nBVD1_1;
++	}
++	state->detect = !(GPLR(cd) & GPIO_bit(cd));
++	state->ready  = !!(GPLR(prdy_nbsy) & GPIO_bit(prdy_nbsy));
++	state->bvd1   = !!(GPLR(nbvd1) & GPIO_bit(nbvd1));
++	state->bvd2   = 1;
++	state->vs_3v  = 0;
++	state->vs_Xv  = 0;
++	state->wrprot = 0;
++}
++
++static int gumstix_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
++				       const socket_state_t *state)
++{
++	return 0;
++}
++
++static void gumstix_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
++{
++	if(skt->nr) {
++		soc_pcmcia_enable_irqs(skt, gumstix_pcmcia_irqs0, ARRAY_SIZE(gumstix_pcmcia_irqs0));
++	} else {
++		soc_pcmcia_enable_irqs(skt, gumstix_pcmcia_irqs1, ARRAY_SIZE(gumstix_pcmcia_irqs1));
++	}
++}
++
++static void gumstix_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
++{
++	if(skt->nr) {
++		soc_pcmcia_disable_irqs(skt, gumstix_pcmcia_irqs0, ARRAY_SIZE(gumstix_pcmcia_irqs0));
++	} else {
++		soc_pcmcia_disable_irqs(skt, gumstix_pcmcia_irqs1, ARRAY_SIZE(gumstix_pcmcia_irqs1));
++	}
++}
++
++static struct pcmcia_low_level gumstix_pcmcia_ops = {
++	.owner			= THIS_MODULE,
++	.hw_init		= gumstix_pcmcia_hw_init,
++	.hw_shutdown		= gumstix_pcmcia_hw_shutdown,
++	.socket_state		= gumstix_pcmcia_socket_state,
++	.configure_socket	= gumstix_pcmcia_configure_socket,
++	.socket_init		= gumstix_pcmcia_socket_init,
++	.socket_suspend		= gumstix_pcmcia_socket_suspend,
++	.nr			= 2,
++};
++
++static struct platform_device *gumstix_pcmcia_device;
++
++extern int __init gumstix_get_cf_cards(void);
++
++#ifdef CONFIG_MACH_GUMSTIX_VERDEX
++extern int __init gumstix_check_if_netCF_vx(void);
++#endif
++
++static int __init gumstix_pcmcia_init(void)
++{
++	int ret;
++
++#ifdef CONFIG_MACH_GUMSTIX_VERDEX
++	net_cf_vx_mode = gumstix_check_if_netCF_vx();
++#endif
++
++	gumstix_pcmcia_ops.nr = gumstix_get_cf_cards();
++
++	gumstix_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
++	if (!gumstix_pcmcia_device)
++		return -ENOMEM;
++
++	ret = platform_device_add_data(gumstix_pcmcia_device, &gumstix_pcmcia_ops,
++				       sizeof(gumstix_pcmcia_ops));
++
++	if (ret == 0) {
++		printk(KERN_INFO "Registering gumstix PCMCIA interface.\n");
++		ret = platform_device_add(gumstix_pcmcia_device);
++	}
++
++	if (ret)
++		platform_device_put(gumstix_pcmcia_device);
++
++	return ret;
++}
++
++static void __exit gumstix_pcmcia_exit(void)
++{
++	/*
++	 * This call is supposed to free our gumstix_pcmcia_device.
++	 * Unfortunately platform_device don't have a free method, and
++	 * we can't assume it's free of any reference at this point so we
++	 * can't free it either.
++	 */
++	platform_device_unregister(gumstix_pcmcia_device);
++}
++
++fs_initcall(gumstix_pcmcia_init);
++module_exit(gumstix_pcmcia_exit);
++
++MODULE_LICENSE("GPL");

target/linux/pxa/patches-3.3/a01-arm-debugll-printk.patch

@@ -0,0 +1,24 @@
+--- a/kernel/printk.c
++++ b/kernel/printk.c
+@@ -44,6 +44,10 @@
+ 
+ #include <asm/uaccess.h>
+ 
++#ifdef CONFIG_DEBUG_LL
++extern void printascii(char *);
++#endif /* CONFIG_DEBUG_LL */
++
+ /*
+  * Architectures can override it:
+  */
+@@ -900,6 +904,10 @@ asmlinkage int vprintk(const char *fmt,
+ 		}
+ 	}
+ 
++#ifdef CONFIG_DEBUG_LL
++	printascii(printk_buf);
++#endif
++
+ 	/*
+ 	 * Copy the output into log_buf. If the caller didn't provide
+ 	 * the appropriate log prefix, we insert them here