ath79: add support for Buffalo WZR-HP-G302H A1A0
Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros AR7242. It is Japanese market model of WZR-HP-G300NH2, but there are some diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx. And, G302H has several hardware versions and hardware is different dependent on the versions. This commit adds support for "A1A0" version. Specification: - Atheros AR7242 - 64 MB of RAM (DDR2) - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 2.4 GHz 2T2R wifi - Atheros AR9283 - 5x 10/100/1000 Mbps Ethernet - Atheros AR8316 - 7x LEDs, 5x keys - LED: 1x gpio-leds, 6x ath9k-leds - key: 3x buttons, 2x slide switches - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/" and move to firmware update page ("ファーム更新") 3. Select the OpenWrt factory image and click update ("更新実行") button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Mathias Kresin
parent
d745eac636
commit
6d1abbcab4
4 changed files with 263 additions and 0 deletions
|
|
@ -42,6 +42,10 @@ ath79_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
;;
|
||||
buffalo,wzr-hp-g302h-a1a0)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
|
||||
;;
|
||||
dlink,dir-825-b1)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
|
|
|
|||
|
|
@ -116,6 +116,7 @@ case "$FIRMWARE" in
|
|||
ath9k_eeprom_extract_reverse "urloader" 5441 1088
|
||||
;;
|
||||
buffalo,whr-g301n|\
|
||||
buffalo,wzr-hp-g302h-a1a0|\
|
||||
tplink,tl-wr841-v5|\
|
||||
tplink,tl-wr941-v4)
|
||||
ath9k_eeprom_extract "art" 4096 3768
|
||||
|
|
|
|||
245
target/linux/ath79/dts/ar7242_buffalo_wzr-hp-g302h-a1a0.dts
Normal file
245
target/linux/ath79/dts/ar7242_buffalo_wzr-hp-g302h-a1a0.dts
Normal file
|
|
@ -0,0 +1,245 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar7242.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "buffalo,wzr-hp-g302h-a1a0", "qca,ar7242";
|
||||
model = "Buffalo WZR-HP-G302H A1A0";
|
||||
|
||||
aliases {
|
||||
led-boot = &diag;
|
||||
led-failsafe = &diag;
|
||||
led-upgrade = &diag;
|
||||
};
|
||||
|
||||
extosc: ref {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
button_usb {
|
||||
label = "usb";
|
||||
linux,code = <BTN_2>;
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
router_on {
|
||||
label = "router_on";
|
||||
linux,code = <BTN_5>;
|
||||
linux,input-type = <EV_SW>;
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
movie_engine {
|
||||
label = "movie_engine";
|
||||
linux,code = <BTN_3>;
|
||||
linux,input-type = <EV_SW>;
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
diag: diag {
|
||||
label = "buffalo:red:diag";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
ath9k-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
usb {
|
||||
label = "buffalo:blue:usb";
|
||||
gpios = <&ath9k 4 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
trigger-sources = <&hub_port>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
wireless {
|
||||
label = "buffalo:green:wireless";
|
||||
gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
security {
|
||||
label = "buffalo:orange:security";
|
||||
gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
router {
|
||||
label = "buffalo:green:router";
|
||||
gpios = <&ath9k 7 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
movie_engine_on {
|
||||
label = "buffalo:blue:movie_engine_on";
|
||||
gpios = <&ath9k 8 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
movie_engine_off {
|
||||
label = "buffalo:blue:movie_engine_off";
|
||||
gpios = <&ath9k 9 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
gpio_usb_power {
|
||||
gpio-export,name = "buffalo:usb-power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
virtual_flash {
|
||||
compatible = "mtd-concat";
|
||||
devices = <&flash0 &flash1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x0 0x40000>;
|
||||
label = "u-boot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
reg = <0x40000 0x10000>;
|
||||
label = "u-boot-env";
|
||||
};
|
||||
|
||||
art: partition@50000 {
|
||||
reg = <0x50000 0x10000>;
|
||||
label = "art";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
reg = <0x60000 0x1f60000>;
|
||||
label = "firmware";
|
||||
};
|
||||
|
||||
partition@1fc0000 {
|
||||
reg = <0x1fc0000 0x40000>;
|
||||
label = "user_property";
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
cs-gpios = <0>, <0>;
|
||||
num-cs = <2>;
|
||||
|
||||
flash0: flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
};
|
||||
|
||||
flash1: flash@1 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <25000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0x1>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x1c000000 0x00000101 0x00001616>;
|
||||
|
||||
mtd-mac-address = <&art 0x120c>;
|
||||
|
||||
phy-mode = "rgmii";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
ath9k: wifi@0,0 {
|
||||
compatible = "pci168c,002a";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mtd-mac-address = <&art 0x120c>;
|
||||
qca,no-eeprom;
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
};
|
||||
};
|
||||
|
||||
&pll {
|
||||
clocks = <&extosc>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
hub_port: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
|
@ -95,6 +95,19 @@ define Device/buffalo_wzr-hp-ag300h
|
|||
endef
|
||||
TARGET_DEVICES += buffalo_wzr-hp-ag300h
|
||||
|
||||
define Device/buffalo_wzr-hp-g302h-a1a0
|
||||
ATH_SOC := ar7242
|
||||
DEVICE_TITLE := Buffalo WZR-HP-G302H A1A0
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
IMAGE_SIZE := 32128k
|
||||
IMAGES += factory.bin tftp.bin
|
||||
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G302H 1.99 | buffalo-tag WZR-HP-G302H 4
|
||||
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
||||
SUPPORTED_DEVICES += wzr-hp-g300nh2
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
|
||||
|
||||
define Device/buffalo_wzr-hp-g450h
|
||||
ATH_SOC := ar7242
|
||||
DEVICE_TITLE := Buffalo WZR-HP-G450H/WZR-450HP
|
||||
|
|
|
|||
Loading…
Reference in a new issue