ar71xx: add support for 8devices Rambutan development board

Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

This commit adds basic support for Rambutan development kit

Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header

Flash instructions:
Stock firmware is OpenWrt, so use:
 sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
 tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit is contained in:
Mantas Pucka 2017-05-08 13:28:38 +03:00 committed by Piotr Dymacz
parent 43a7a1a05e
commit 68b5d34f69
11 changed files with 132 additions and 0 deletions

View file

@ -74,6 +74,9 @@ case "$FIRMWARE" in
ath9k_eeprom_extract "caldata" 4096 2048
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 0)
;;
rambutan)
ath9k_eeprom_extract "art" 4096 2048
;;
z1)
. /lib/upgrade/nand.sh

View file

@ -811,6 +811,9 @@ ar71xx_board_detect() {
*"R6100")
name="r6100"
;;
*"Rambutan"*)
name="rambutan"
;;
*"RE450")
name="re450"
;;

View file

@ -44,6 +44,12 @@ preinit_set_mac_address() {
mac_wan=$(mtd_get_mac_binary caldata 6)
[ -n "$mac_wan" ] && ifconfig eth0 hw ether "$mac_wan"
;;
rambutan)
mac_lan=$(mtd_get_mac_binary art 0)
[ -n "$mac_lan" ] && ifconfig eth0 hw ether "$mac_lan"
mac_wan=$(mtd_get_mac_binary art 6)
[ -n "$mac_wan" ] && ifconfig eth1 hw ether "$mac_wan"
;;
tew-632brp)
fetch_mac_from_mtd config lan_mac wan_mac
;;

View file

@ -521,6 +521,7 @@ platform_check_image() {
c-60|\
nbg6716|\
r6100|\
rambutan|\
wndr3700v4|\
wndr4300)
nand_do_platform_check $board $1
@ -663,6 +664,7 @@ platform_pre_upgrade() {
c-60|\
nbg6716|\
r6100|\
rambutan|\
rb-411|\
rb-411u|\
rb-433|\

View file

@ -146,6 +146,7 @@ CONFIG_ATH79_MACH_PQI_AIR_PEN=y
CONFIG_ATH79_MACH_QIHOO_C301=y
CONFIG_ATH79_MACH_R602N=y
CONFIG_ATH79_MACH_R6100=y
# CONFIG_ATH79_MACH_RAMBUTAN is not set
# CONFIG_ATH79_MACH_RB2011 is not set
# CONFIG_ATH79_MACH_RB4XX is not set
# CONFIG_ATH79_MACH_RB750 is not set

View file

@ -1897,6 +1897,16 @@ config ATH79_MACH_LIMA
select ATH79_DEV_WMAC
select ATH79_DEV_ETH
config ATH79_MACH_RAMBUTAN
bool "8devices Rambutan board"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E316N_V2
bool "COMFAST CF-E316N v2 support"
select SOC_AR934X

View file

@ -137,6 +137,7 @@ obj-$(CONFIG_ATH79_MACH_MZK_W04NU) += mach-mzk-w04nu.o
obj-$(CONFIG_ATH79_MACH_MZK_W300NH) += mach-mzk-w300nh.o
obj-$(CONFIG_ATH79_MACH_NBG460N) += mach-nbg460n.o
obj-$(CONFIG_ATH79_MACH_NBG6716) += mach-nbg6716.o
obj-$(CONFIG_ATH79_MACH_RAMBUTAN) += mach-rambutan.o
obj-$(CONFIG_ATH79_MACH_OM2P) += mach-om2p.o
obj-$(CONFIG_ATH79_MACH_OM5P) += mach-om5p.o
obj-$(CONFIG_ATH79_MACH_OM5P_AC) += mach-om5pac.o

View file

@ -0,0 +1,90 @@
/*
* 8devices Rambutan board support
*
* Copyright (C) 2017 Mantas Pucka <mantas@8devices.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/pci.h>
#include <linux/phy.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
#include <asm/mach-ath79/ath79.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include <linux/platform/ar934x_nfc.h>
#include <linux/ar8216_platform.h>
#include <linux/platform_data/phy-at803x.h>
#include "common.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-spi.h"
#include "dev-nfc.h"
#include "dev-usb.h"
#include "dev-wmac.h"
#include "machtypes.h"
#include "pci.h"
static struct at803x_platform_data rambutan_ar8032_data = {
.has_reset_gpio = 1,
.reset_gpio = 17,
};
static struct mdio_board_info rambutan_mdio0_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.phy_addr = 0,
.platform_data = &rambutan_ar8032_data,
},
};
static struct at803x_platform_data rambutan_ar8033_data = {
.has_reset_gpio = 1,
.reset_gpio = 23,
};
static struct mdio_board_info rambutan_mdio1_info[] = {
{
.bus_id = "ag71xx-mdio.1",
.phy_addr = 0,
.platform_data = &rambutan_ar8033_data,
},
};
static void __init rambutan_setup(void)
{
ath79_nfc_set_ecc_mode(AR934X_NFC_ECC_HW);
ath79_register_nfc();
ath79_register_usb();
ath79_register_pci();
ath79_register_wmac_simple();
mdiobus_register_board_info(rambutan_mdio0_info,
ARRAY_SIZE(rambutan_mdio0_info));
mdiobus_register_board_info(rambutan_mdio1_info,
ARRAY_SIZE(rambutan_mdio1_info));
ath79_register_mdio(0, 0x0);
ath79_register_mdio(1, 0x0);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_register_eth(0);
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
ath79_eth1_data.phy_mask = BIT(0);
ath79_eth1_data.mii_bus_dev = &ath79_mdio1_device.dev;
ath79_eth1_pll_data.pll_1000 = 0x17000000;
ath79_eth1_pll_data.pll_10 = 0x1313;
ath79_register_eth(1);
}
MIPS_MACHINE(ATH79_MACH_RAMBUTAN, "RAMBUTAN", "8devices Rambutan board",
rambutan_setup);

View file

@ -155,6 +155,7 @@ enum ath79_mach_type {
ATH79_MACH_QIHOO_C301, /* Qihoo 360 C301 */
ATH79_MACH_R602N, /* P&W R602N */
ATH79_MACH_R6100, /* NETGEAR R6100 */
ATH79_MACH_RAMBUTAN, /* 8devices Rambutan */
ATH79_MACH_RB_2011G, /* Mikrotik RouterBOARD 2011UAS-2HnD */
ATH79_MACH_RB_2011L, /* Mikrotik RouterBOARD 2011L */
ATH79_MACH_RB_2011R5, /* Mikrotik RouterBOARD 2011UiAS(-2Hnd) */

View file

@ -52,6 +52,20 @@ define Build/MerakiNAND-old
@mv $@.new $@
endef
define Device/rambutan
DEVICE_TITLE := 8devices Rambutan
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = RAMBUTAN
BLOCKSIZE = 128KiB
MTDPARTS = ar934x-nfc:3M(u-boot)ro,2M(u-boot-env),1M(art),122M(ubi)
PAGESIZE := 2048
KERNEL_IN_UBI := 1
IMAGES := factory.ubi sysupgrade.tar
IMAGE/sysupgrade.tar := sysupgrade-tar
IMAGE/factory.ubi := append-ubi
endef
TARGET_DEVICES += rambutan
define Device/z1
DEVICE_TITLE := Meraki Z1
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-spi-gpio kmod-ath9k kmod-owl-loader

View file

@ -106,6 +106,7 @@
# CONFIG_ATH79_MACH_PQI_AIR_PEN is not set
# CONFIG_ATH79_MACH_QIHOO_C301 is not set
# CONFIG_ATH79_MACH_R602N is not set
CONFIG_ATH79_MACH_RAMBUTAN=y
# CONFIG_ATH79_MACH_RE450 is not set
# CONFIG_ATH79_MACH_RW2458N is not set
# CONFIG_ATH79_MACH_SC1750 is not set