lantiq: add Netgear DM200 support
Netgear DM200 is an inexpensive VDSL modem:
CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
RAM: 64MiB
Flash: 8MiB
Ethernet: 1x100M
DSL: VDSL2+, ADSL2+
reset button, 3x bi-color LEDs
Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.
To upgrade from the vendor firmware, upload factory.img
The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.
Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.
Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
This commit is contained in:
Thomas Nixon
Mathias Kresin
parent
08cd5b769d
commit
50e3659703
4 changed files with 234 additions and 0 deletions
|
|
@ -50,6 +50,9 @@ ARV7519RW22)
|
|||
BTHOMEHUBV5A)
|
||||
ucidef_set_led_default "dimmed" "dimmed" "dimmed" "0"
|
||||
;;
|
||||
DM200)
|
||||
ucidef_set_led_netdev "lan" "lan" "dm200:green:lan" "eth0"
|
||||
;;
|
||||
FRITZ7320)
|
||||
ucidef_set_led_netdev "wifi" "wifi" "fritz7320:green:wlan" "wlan0"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -100,6 +100,12 @@ DGN3500*)
|
|||
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5t@eth0"
|
||||
;;
|
||||
|
||||
DM200)
|
||||
lan_mac=$(mtd_get_mac_binary ART 0)
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
ucidef_set_interface_lan 'eth0'
|
||||
;;
|
||||
|
||||
EASY80920NAND|EASY80920NOR)
|
||||
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
|
|
|
|||
214
target/linux/lantiq/dts/DM200.dts
Normal file
214
target/linux/lantiq/dts/DM200.dts
Normal file
|
|
@ -0,0 +1,214 @@
|
|||
/dts-v1/;
|
||||
|
||||
#include "vr9.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "DM200 - Netgear DM200";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyLTQ0,115200";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power_green;
|
||||
led-failsafe = &power_amber;
|
||||
led-running = &power_green;
|
||||
|
||||
led-dsl = &dsl_green;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
reg = <0x0 0x4000000>;
|
||||
};
|
||||
|
||||
fpi@10000000 {
|
||||
gpio: pinmux@E100B10 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&state_default>;
|
||||
|
||||
state_default: pinmux {
|
||||
mdio {
|
||||
lantiq,groups = "mdio";
|
||||
lantiq,function = "mdio";
|
||||
};
|
||||
};
|
||||
|
||||
pins_spi_default: pins_spi_default {
|
||||
spi_in {
|
||||
lantiq,groups = "spi_di";
|
||||
lantiq,function = "spi";
|
||||
};
|
||||
spi_out {
|
||||
lantiq,groups = "spi_do", "spi_clk", "spi_cs4";
|
||||
lantiq,function = "spi";
|
||||
lantiq,output = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pcie@d900000 {
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
gphy-xrx200 {
|
||||
compatible = "lantiq,phy-xrx200";
|
||||
firmware = "lantiq/vr9_phy22f_a2x.bin";
|
||||
phys = [ 01 ];
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <100>;
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
annexa {
|
||||
gpio-export,name = "annexa";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
annexb {
|
||||
gpio-export,name = "annexb";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power_amber: power_amber {
|
||||
label = "dm200:amber:power";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
power_green: power_green {
|
||||
label = "dm200:green:power";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lan_amber {
|
||||
label = "dm200:amber:lan";
|
||||
gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
lan_green {
|
||||
label = "dm200:green:lan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
dsl_amber {
|
||||
label = "dm200:amber:dsl";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
dsl_green: dsl_green {
|
||||
label = "dm200:green:dsl";
|
||||
gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pins_spi_default>;
|
||||
|
||||
status = "ok";
|
||||
|
||||
m25p80@4 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <4 0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x0 0x20000>;
|
||||
label = "uboot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
reg = <0x20000 0x10000>;
|
||||
label = "gphyfirmware";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
reg = <0x30000 0x7b0000>;
|
||||
label = "firmware";
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
reg = <0x7e0000 0x10000>;
|
||||
label = "sysconfig";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7f0000 {
|
||||
reg = <0x7f0000 0x2000>;
|
||||
label = "ubootconfig";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7f2000 {
|
||||
reg = <0x7f2000 0x1000>;
|
||||
label = "ART";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7f3000 {
|
||||
reg = <0x7f3000 0x1000>;
|
||||
label = "pot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7f4000 {
|
||||
reg = <0x7f4000 0xc000>;
|
||||
label = "ret";
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
lan: interface@0 {
|
||||
compatible = "lantiq,xrx200-pdi";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0>;
|
||||
|
||||
ethernet@4 {
|
||||
compatible = "lantiq,xrx200-pdi-port";
|
||||
reg = <4>;
|
||||
phy-mode = "mii";
|
||||
phy-handle = <&phy13>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "lantiq,xrx200-mdio";
|
||||
phy13: ethernet-phy@13 {
|
||||
reg = <0x13>;
|
||||
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -513,6 +513,17 @@ define Device/BTHOMEHUBV5A
|
|||
endef
|
||||
TARGET_DEVICES += BTHOMEHUBV5A
|
||||
|
||||
define Device/DM200
|
||||
IMAGES := sysupgrade.bin factory.img
|
||||
IMAGE/factory.img := $$(IMAGE/sysupgrade.bin) | netgear-dni
|
||||
IMAGE_SIZE := 7872k
|
||||
DEVICE_TITLE := Netgear DM200
|
||||
NETGEAR_BOARD_ID := DM200
|
||||
NETGEAR_HW_ID := 29765233+8+0+64+0+0
|
||||
endef
|
||||
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
||||
TARGET_DEVICES += DM200
|
||||
|
||||
define Device/EASY80920NAND
|
||||
$(Device/lantiqFullImage)
|
||||
IMAGE_SIZE := 64512k
|
||||
|
|
|
|||
Loading…
Reference in a new issue