ipq40xx: add support for EnGenius EAP1300

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
NOR:    32 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button
LEDS:   Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm

2. Load image via GUI

a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.

3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin

Signed-off-by: Steven Lin <steven.lin@senao.com>
This commit is contained in:
Steven Lin 2018-10-19 16:55:08 +08:00 committed by Mathias Kresin
parent e261c8b764
commit 2b4ac79a79
8 changed files with 263 additions and 8 deletions

View file

@ -17,7 +17,7 @@ endef
# Please send a mail with your device-specific board files upstream.
# You can find instructions and examples on the linux-wireless wiki:
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
ALLWIFIBOARDS:=
ALLWIFIBOARDS:=engenius_eap1300
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
@ -52,5 +52,6 @@ Don't install it for any other device!
endef
#$(eval $(call generate-ipq-wifi-package,<devicename>,<filename>,<displayname>))
$(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))

Binary file not shown.

View file

@ -23,6 +23,12 @@ avm,fritzbox-4040)
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
;;
engenius,eap1300)
ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
;;
glinet,gl-b1300)
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
;;

View file

@ -33,6 +33,13 @@ avm,fritzbox-4040)
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
engenius,eap1300 |\
meraki,mr33 |\
netgear,ex6100v2 |\
netgear,ex6150v2 |\
zyxel,wre6606)
ucidef_set_interface_lan "eth0"
;;
glinet,gl-b1300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
@ -42,12 +49,6 @@ openmesh,a42 |\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
meraki,mr33 |\
netgear,ex6100v2 |\
netgear,ex6150v2 |\
zyxel,wre6606)
ucidef_set_interface_lan "eth0"
;;
zyxel,nbg6617)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \

View file

@ -142,6 +142,7 @@ case "$FIRMWARE" in
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
;;
compex,wpj428 |\
engenius,eap1300 |\
openmesh,a42 |\
openmesh,a62)
ath10kcal_extract "0:ART" 4096 12064
@ -178,6 +179,7 @@ case "$FIRMWARE" in
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
;;
compex,wpj428 |\
engenius,eap1300 |\
openmesh,a42 |\
openmesh,a62)
ath10kcal_extract "0:ART" 20480 12064

View file

@ -0,0 +1,230 @@
// SPDX-License-Identifier: GPL-2.0-or-later
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "EnGenius EAP1300";
compatible = "engenius,eap1300", "qcom,ipq4019";
soc {
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
serial@78af000 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
};
gpio-keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_RESTART>;
};
};
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
};
gpio-leds {
compatible = "gpio-leds";
power: orange {
label = "eap1300:orange:power";
gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
};
lan {
label = "eap1300:blue:lan";
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
};
mesh {
label = "eap1300:blue:mesh";
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
};
wlan2g {
label = "eap1300:blue:wlan2g";
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
};
wlan5g {
label = "eap1300:yellow:wlan5g";
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
};
};
};
&tlmm {
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi_0_pins: spi_0_pinmux {
pin {
function = "blsp_spi0";
pins = "gpio54", "gpio55", "gpio56", "gpio57";
drive-strength = <12>;
bias-disable;
};
pin_cs {
function = "gpio";
pins = "gpio54";
drive-strength = <2>;
bias-disable;
output-high;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_spi1 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "okay";
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
m25p80@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "0:SBL1";
reg = <0x00000000 0x00040000>;
read-only;
};
partition1@40000 {
label = "0:MIBIB";
reg = <0x00040000 0x00020000>;
read-only;
};
partition2@60000 {
label = "0:QSEE";
reg = <0x00060000 0x00060000>;
read-only;
};
partition3@c0000 {
label = "0:CDT";
reg = <0x000c0000 0x00010000>;
read-only;
};
partition4@d0000 {
label = "0:DDRPARAMS";
reg = <0x000d0000 0x00010000>;
read-only;
};
partition5@e0000 {
label = "0:APPSBLENV";
reg = <0x000e0000 0x00010000>;
read-only;
};
partition6@f0000 {
label = "0:APPSBL";
reg = <0x000f0000 0x00090000>;
read-only;
};
partition7@180000 {
label = "0:ART";
reg = <0x00180000 0x00010000>;
read-only;
};
partition8@190000 {
label = "firmware";
reg = <0x190000 0x1dc0000>;
};
partition9@1f50000 {
label = "u-boot-env";
reg = <0x01f50000 0x00010000>;
};
partition10@1f60000 {
label = "userconfig";
reg = <0x01f60000 0x000a0000>;
};
};
};
};
&cryptobam {
status = "okay";
};
&gmac0 {
vlan_tag = <2 0x20>;
};
&gmac1 {
vlan_tag = <1 0x10>;
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
};

View file

@ -105,6 +105,20 @@ define Device/compex_wpj428
endef
TARGET_DEVICES += compex_wpj428
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_TITLE := EnGenius EAP1300
DEVICE_DTS_CONFIG := config@4
BOARD_NAME := eap1300
DEVICE_DTS := qcom-ipq4018-eap1300
KERNEL_SIZE := 5120k
IMAGE_SIZE := 25344k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-engenius_eap1300
endef
TARGET_DEVICES += engenius_eap1300
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_TITLE := GL.iNet GL-B1300

View file

@ -10,11 +10,12 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -697,7 +697,20 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -697,7 +697,21 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-a42.dtb \
+ qcom-ipq4018-eap1300.dtb \
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \
+ qcom-ipq4018-fritz4040.dtb \