adm5120: add support for 3.8

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35769

target/linux/adm5120/config-3.8

@@ -0,0 +1,190 @@
+CONFIG_ADM5120=y
+CONFIG_ADM5120_ENET=y
+CONFIG_ADM5120_MACH_5GXI=y
+CONFIG_ADM5120_MACH_BR_6104K=y
+CONFIG_ADM5120_MACH_BR_6104KP=y
+CONFIG_ADM5120_MACH_BR_61X4WG=y
+CONFIG_ADM5120_MACH_CAS_771=y
+CONFIG_ADM5120_MACH_EASY5120P_ATA=y
+CONFIG_ADM5120_MACH_EASY5120_RT=y
+CONFIG_ADM5120_MACH_EASY5120_WVOIP=y
+CONFIG_ADM5120_MACH_EASY83000=y
+CONFIG_ADM5120_MACH_EB_214A=y
+CONFIG_ADM5120_MACH_NFS_101=y
+CONFIG_ADM5120_MACH_NP27G=y
+CONFIG_ADM5120_MACH_NP28G=y
+CONFIG_ADM5120_MACH_PMUGW=y
+# CONFIG_ADM5120_MACH_RB_11X is not set
+# CONFIG_ADM5120_MACH_RB_133 is not set
+# CONFIG_ADM5120_MACH_RB_133C is not set
+# CONFIG_ADM5120_MACH_RB_150 is not set
+# CONFIG_ADM5120_MACH_RB_153 is not set
+# CONFIG_ADM5120_MACH_RB_192 is not set
+CONFIG_ADM5120_MACH_WP54=y
+CONFIG_ADM5120_OEM_CELLVISION=y
+CONFIG_ADM5120_OEM_COMPEX=y
+CONFIG_ADM5120_OEM_EDIMAX=y
+CONFIG_ADM5120_OEM_GENERIC=y
+CONFIG_ADM5120_OEM_INFINEON=y
+# CONFIG_ADM5120_OEM_MIKROTIK is not set
+CONFIG_ADM5120_OEM_MOTOROLA=y
+CONFIG_ADM5120_OEM_OSBRIDGE=y
+# CONFIG_ADM5120_OEM_ZYXEL is not set
+CONFIG_ADM5120_SOC_BGA=y
+CONFIG_ADM5120_WDT=y
+CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
+CONFIG_ARCH_DISCARD_MEMBLOCK=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM_AMBA=y
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_ATA=m
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CMDLINE="console=ttyAM0,115200 rootfstype=squashfs,jffs2"
+CONFIG_CMDLINE_BOOL=y
+# CONFIG_CMDLINE_OVERRIDE is not set
+# CONFIG_CPU_BIG_ENDIAN is not set
+CONFIG_CPU_GENERIC_DUMP_TLB=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_CPU_R4K_CACHE_TLB=y
+CONFIG_CPU_R4K_FPU=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_CSRC_R4K=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_WORK=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HID=m
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+# CONFIG_HOSTAP_FIRMWARE_NVRAM is not set
+CONFIG_HOSTAP_PCI=m
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_IMAGE_CMDLINE_HACK=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INPUT=m
+# CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set
+CONFIG_IRQ_CPU=y
+CONFIG_IRQ_FORCED_THREADING=y
+# CONFIG_LEDS_TRIGGER_ADM5120_SWITCH is not set
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_LIB80211=m
+CONFIG_LIB80211_CRYPT_CCMP=m
+CONFIG_LIB80211_CRYPT_TKIP=m
+CONFIG_LIB80211_CRYPT_WEP=m
+CONFIG_MII=m
+CONFIG_MIPS=y
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+CONFIG_MIPS_MACHINE=y
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_SEAD3 is not set
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_ADM5120=y
+CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_MYLOADER_PARTS=y
+CONFIG_MTD_TRXSPLIT=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NLS=m
+CONFIG_NO_EXCEPT_FILL=y
+CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
+CONFIG_NO_HZ=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_PCI=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PERF_USE_VMALLOC=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_SCSI=m
+CONFIG_SCSI_MOD=m
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SOFT_WATCHDOG=m
+# CONFIG_SWAP is not set
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_UIDGID_CONVERTED=y
+CONFIG_USB=m
+CONFIG_USB_ADM5120_HCD=m
+CONFIG_USB_ARCH_HAS_XHCI=y
+CONFIG_USB_COMMON=m
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_EHCI_HCD_PLATFORM is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_OHCI_HCD_PLATFORM is not set
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_UHCI_HCD is not set
+CONFIG_WATCHDOG_CORE=y
+CONFIG_ZONE_DMA_FLAG=0

target/linux/adm5120/patches-3.8/001-adm5120.patch

@@ -0,0 +1,44 @@
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -51,6 +51,24 @@ choice
+ 	prompt "System type"
+ 	default SGI_IP22
+ 
++config ADM5120
++	bool "Infineon/ADMtek ADM5120 SoC based machines"
++	select BOOT_RAW
++	select NO_EXCEPT_FILL
++	select CEVT_R4K
++	select CSRC_R4K
++	select SYS_HAS_CPU_MIPS32_R1
++	select SYS_HAS_EARLY_PRINTK
++	select DMA_NONCOHERENT
++	select IRQ_CPU
++	select SYS_SUPPORTS_LITTLE_ENDIAN
++	select SYS_SUPPORTS_BIG_ENDIAN
++	select SYS_SUPPORTS_32BIT_KERNEL
++	select ARCH_REQUIRE_GPIOLIB
++	select SWAP_IO_SPACE if CPU_BIG_ENDIAN
++	select MIPS_MACHINE
++	select HAVE_CLK
++
+ config MIPS_ALCHEMY
+ 	bool "Alchemy processor based machines"
+ 	select 64BIT_PHYS_ADDR
+@@ -836,6 +854,7 @@ config NLM_XLP_BOARD
+ 
+ endchoice
+ 
++source "arch/mips/adm5120/Kconfig"
+ source "arch/mips/alchemy/Kconfig"
+ source "arch/mips/ath79/Kconfig"
+ source "arch/mips/bcm47xx/Kconfig"
+--- a/arch/mips/Kbuild.platforms
++++ b/arch/mips/Kbuild.platforms
+@@ -1,5 +1,6 @@
+ # All platforms listed in alphabetic order
+ 
++platforms += adm5120
+ platforms += alchemy
+ platforms += ar7
+ platforms += ath79

target/linux/adm5120/patches-3.8/002-adm5120_flash.patch

@@ -0,0 +1,21 @@
+--- a/drivers/mtd/maps/Kconfig
++++ b/drivers/mtd/maps/Kconfig
+@@ -501,4 +501,8 @@ config MTD_LATCH_ADDR
+ 
+           If compiled as a module, it will be called latch-addr-flash.
+ 
++config MTD_ADM5120
++	tristate "Map driver for ADM5120 based boards"
++	depends on ADM5120
++
+ endmenu
+--- a/drivers/mtd/maps/Makefile
++++ b/drivers/mtd/maps/Makefile
+@@ -37,6 +37,7 @@ obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx2
+ obj-$(CONFIG_MTD_DBOX2)		+= dbox2-flash.o
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI)		+= pci.o
++obj-$(CONFIG_MTD_ADM5120)	+= adm5120-flash.o
+ obj-$(CONFIG_MTD_AUTCPU12)	+= autcpu12-nvram.o
+ obj-$(CONFIG_MTD_IMPA7)		+= impa7.o
+ obj-$(CONFIG_MTD_UCLINUX)	+= uclinux.o

target/linux/adm5120/patches-3.8/003-adm5120_switch.patch

@@ -0,0 +1,23 @@
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -255,6 +255,10 @@ source "drivers/net/dsa/Kconfig"
+ 
+ source "drivers/net/ethernet/Kconfig"
+ 
++config ADM5120_ENET
++	tristate "ADM5120 Ethernet switch support"
++	depends on ADM5120
++
+ source "drivers/net/fddi/Kconfig"
+ 
+ source "drivers/net/hippi/Kconfig"
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -33,6 +33,7 @@ obj-$(CONFIG_CAN) += can/
+ obj-$(CONFIG_ETRAX_ETHERNET) += cris/
+ obj-$(CONFIG_NET_DSA) += dsa/
+ obj-$(CONFIG_ETHERNET) += ethernet/
++obj-$(CONFIG_ADM5120_ENET) += adm5120sw.o
+ obj-$(CONFIG_FDDI) += fddi/
+ obj-$(CONFIG_HIPPI) += hippi/
+ obj-$(CONFIG_HAMRADIO) += hamradio/

target/linux/adm5120/patches-3.8/005-adm5120_usb.patch

@@ -0,0 +1,33 @@
+--- a/drivers/usb/Makefile
++++ b/drivers/usb/Makefile
+@@ -13,6 +13,7 @@ obj-$(CONFIG_USB_DWC3)		+= dwc3/
+ obj-$(CONFIG_USB_MON)		+= mon/
+ 
+ obj-$(CONFIG_PCI)		+= host/
++obj-$(CONFIG_USB_ADM5120_HCD)	+= host/
+ obj-$(CONFIG_USB_EHCI_HCD)	+= host/
+ obj-$(CONFIG_USB_ISP116X_HCD)	+= host/
+ obj-$(CONFIG_USB_OHCI_HCD)	+= host/
+--- a/drivers/usb/host/Kconfig
++++ b/drivers/usb/host/Kconfig
+@@ -4,6 +4,10 @@
+ comment "USB Host Controller Drivers"
+ 	depends on USB
+ 
++config USB_ADM5120_HCD
++	tristate "ADM5120 HCD support (EXPERIMENTAL)"
++	depends on USB && ADM5120 && EXPERIMENTAL
++
+ config USB_C67X00_HCD
+ 	tristate "Cypress C67x00 HCD support"
+ 	depends on USB
+--- a/drivers/usb/host/Makefile
++++ b/drivers/usb/host/Makefile
+@@ -23,6 +23,7 @@ obj-$(CONFIG_USB_WHCI_HCD)	+= whci/
+ 
+ obj-$(CONFIG_PCI)		+= pci-quirks.o
+ 
++obj-$(CONFIG_USB_ADM5120_HCD)	+= adm5120-hcd.o
+ obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
+ obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
+ obj-$(CONFIG_USB_EHCI_HCD_PLATFORM)	+= ehci-platform.o

target/linux/adm5120/patches-3.8/007-adm5120_pci.patch

@@ -0,0 +1,22 @@
+--- a/arch/mips/pci/Makefile
++++ b/arch/mips/pci/Makefile
+@@ -18,6 +18,7 @@ obj-$(CONFIG_PCI_TX4927)	+= ops-tx4927.o
+ obj-$(CONFIG_BCM47XX)		+= pci-bcm47xx.o
+ obj-$(CONFIG_BCM63XX)		+= pci-bcm63xx.o fixup-bcm63xx.o \
+ 					ops-bcm63xx.o
++obj-$(CONFIG_ADM5120)		+= pci-adm5120.o
+ obj-$(CONFIG_MIPS_ALCHEMY)	+= pci-alchemy.o
+ obj-$(CONFIG_SOC_AR71XX)	+= pci-ar71xx.o
+ obj-$(CONFIG_PCI_AR724X)	+= pci-ar724x.o
+--- a/include/linux/pci_ids.h
++++ b/include/linux/pci_ids.h
+@@ -1807,6 +1807,9 @@
+ #define PCI_VENDOR_ID_ESDGMBH		0x12fe
+ #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
+ 
++#define PCI_VENDOR_ID_ADMTEK		0x1317
++#define PCI_DEVICE_ID_ADMTEK_ADM5120	0x5120
++
+ #define PCI_VENDOR_ID_SIIG		0x131f
+ #define PCI_SUBVENDOR_ID_SIIG		0x131f
+ #define PCI_DEVICE_ID_SIIG_1S_10x_550	0x1000

target/linux/adm5120/patches-3.8/009-adm5120_leds_switch_trigger.patch

@@ -0,0 +1,22 @@
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -579,4 +579,12 @@ config LEDS_TRIGGER_USBDEV
+ 	  This allows LEDs to be controlled by the presence/activity of
+ 	  an USB device. If unsure, say N.
+ 
++config LEDS_TRIGGER_ADM5120_SWITCH
++	tristate "LED ADM5120 Switch Port Status Trigger"
++	depends on LEDS_TRIGGERS && ADM5120
++	help
++	  This allows LEDs to be controlled by the port states of
++	  the ADM5120 built-in Ethernet Switch
++	  If unsure, say N.
++
+ endif # NEW_LEDS
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -68,3 +68,4 @@ obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT)	+=
+ obj-$(CONFIG_LEDS_TRIGGER_MORSE)	+= ledtrig-morse.o
+ obj-$(CONFIG_LEDS_TRIGGER_NETDEV)	+= ledtrig-netdev.o
+ obj-$(CONFIG_LEDS_TRIGGER_USBDEV)	+= ledtrig-usbdev.o
++obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o

target/linux/adm5120/patches-3.8/101-cfi_fixup_macronix_bootloc.patch

@@ -0,0 +1,84 @@
+--- a/drivers/mtd/chips/cfi_cmdset_0002.c
++++ b/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -48,6 +48,12 @@
+ #define SST49LF008A		0x005a
+ #define AT49BV6416		0x00d6
+ 
++/* Macronix */
++#define MX29LV160B	0x2249	/* MX29LV160 Bottom-boot chip */
++#define MX29LV160T	0x22C4	/* MX29LV160 Top-boot chip */
++#define MX29LV320B	0x22A8	/* MX29LV320 Bottom-boot chip */
++#define MX29LV320T	0x22A7	/* MX29LV320 Top-boot chip */
++
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+@@ -358,6 +364,41 @@ static struct cfi_fixup cfi_nopri_fixup_
+ 	{ 0, 0, NULL }
+ };
+ 
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++/*
++ * Some Macronix chips has no/bad bootblock information in the CFI table
++ */
++static void fixup_macronix_bootloc(struct mtd_info *mtd)
++{
++	struct map_info *map = mtd->priv;
++	struct cfi_private *cfi = map->fldrv_priv;
++	struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
++	__u8 t;
++
++	switch (cfi->id) {
++	/* TODO: put affected chip ids here */
++	case MX29LV160B:
++	case MX29LV320B:
++		t = 2;	/* Bottom boot */
++		break;
++	case MX29LV160T:
++	case MX29LV320T:
++		t = 3;	/* Top boot */
++		break;
++	default:
++		return;
++	}
++
++	if (extp->TopBottom == t)
++		/* boot location detected by the CFI layer is correct */
++		return;
++
++	extp->TopBottom = t;
++	printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
++		"to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
++}
++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
++
+ static struct cfi_fixup cfi_fixup_table[] = {
+ 	{ CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri },
+ #ifdef AMD_BOOTLOC_BUG
+@@ -400,6 +441,9 @@ static struct cfi_fixup fixup_table[] =
+ 	 */
+ 	{ CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip },
+ 	{ CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock },
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++	{ CFI_MFR_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc },
++#endif
+ 	{ 0, 0, NULL }
+ };
+ 
+--- a/drivers/mtd/chips/Kconfig
++++ b/drivers/mtd/chips/Kconfig
+@@ -189,6 +189,14 @@ config MTD_CFI_AMDSTD
+ 	  provides support for one of those command sets, used on chips
+ 	  including the AMD Am29LV320.
+ 
++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++	bool "Fix boot-block location for Macronix flash chips"
++	depends on MTD_CFI_AMDSTD
++	help
++	  Some Macronix flash chips have no/wrong boot-block location in the
++	  CFI table, and the driver may detect the type incorrectly. Select
++	  this if your board has such chip.
++
+ config MTD_CFI_STAA
+ 	tristate "Support for ST (Advanced Architecture) flash chips"
+ 	depends on MTD_GEN_PROBE

target/linux/adm5120/patches-3.8/102-jedec_pmc_39lvxxx_chips.patch

@@ -0,0 +1,68 @@
+--- a/drivers/mtd/chips/jedec_probe.c
++++ b/drivers/mtd/chips/jedec_probe.c
+@@ -115,6 +115,10 @@
+ #define UPD29F064115	0x221C
+ 
+ /* PMC */
++#define PM39LV512	0x001B
++#define PM39LV010	0x001C
++#define PM39LV020	0x003D
++#define PM39LV040	0x003E
+ #define PM49FL002	0x006D
+ #define PM49FL004	0x006E
+ #define PM49FL008	0x006A
+@@ -1259,6 +1263,54 @@ static const struct amd_flash_info jedec
+ 			ERASEINFO(0x02000,2),
+ 			ERASEINFO(0x04000,1),
+ 		}
++        }, {
++		.mfr_id		= CFI_MFR_PMC,
++		.dev_id		= PM39LV512,
++		.name		= "PMC Pm39LV512",
++		.devtypes	= CFI_DEVICETYPE_X8,
++		.uaddr		= MTD_UADDR_0x0555_0x02AA,
++		.dev_size	= SIZE_64KiB,
++		.cmd_set	= P_ID_AMD_STD,
++		.nr_regions	= 1,
++		.regions	= {
++			ERASEINFO(0x01000,16),
++		}
++        }, {
++		.mfr_id		= CFI_MFR_PMC,
++		.dev_id		= PM39LV010,
++		.name		= "PMC Pm39LV010",
++		.devtypes	= CFI_DEVICETYPE_X8,
++		.uaddr		= MTD_UADDR_0x0555_0x02AA,
++		.dev_size	= SIZE_128KiB,
++		.cmd_set	= P_ID_AMD_STD,
++		.nr_regions	= 1,
++		.regions	= {
++			ERASEINFO(0x01000,32),
++		}
++        }, {
++		.mfr_id		= CFI_MFR_PMC,
++		.dev_id		= PM39LV020,
++		.name		= "PMC Pm39LV020",
++		.devtypes	= CFI_DEVICETYPE_X8,
++		.uaddr		= MTD_UADDR_0x0555_0x02AA,
++		.dev_size	= SIZE_256KiB,
++		.cmd_set	= P_ID_AMD_STD,
++		.nr_regions	= 1,
++		.regions	= {
++			ERASEINFO(0x01000,64),
++		}
++        }, {
++		.mfr_id		= CFI_MFR_PMC,
++		.dev_id		= PM39LV040,
++		.name		= "PMC Pm39LV040",
++		.devtypes	= CFI_DEVICETYPE_X8,
++		.uaddr		= MTD_UADDR_0x0555_0x02AA,
++		.dev_size	= SIZE_512KiB,
++		.cmd_set	= P_ID_AMD_STD,
++		.nr_regions	= 1,
++		.regions	= {
++			ERASEINFO(0x01000,128),
++		}
+ 	}, {
+ 		.mfr_id		= CFI_MFR_PMC,
+ 		.dev_id		= PM49FL002,

target/linux/adm5120/patches-3.8/103-mtd_trxsplit.patch

@@ -0,0 +1,23 @@
+--- a/drivers/mtd/Kconfig
++++ b/drivers/mtd/Kconfig
+@@ -31,6 +31,10 @@ config MTD_ROOTFS_SPLIT
+ 	bool "Automatically split 'rootfs' partition for squashfs"
+ 	default y
+ 
++config MTD_TRXSPLIT
++	bool "Automatically find and split TRX partitions"
++	default n
++
+ config MTD_REDBOOT_PARTS
+ 	tristate "RedBoot partition table parsing"
+ 	---help---
+--- a/drivers/mtd/Makefile
++++ b/drivers/mtd/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_AR7_PARTS)	+= ar7part.o
+ obj-$(CONFIG_MTD_BCM63XX_PARTS)	+= bcm63xxpart.o
+ obj-$(CONFIG_MTD_BCM47XX_PARTS)	+= bcm47xxpart.o
+ obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
++obj-$(CONFIG_MTD_TRXSPLIT)	+= trxsplit.o
+ 
+ # 'Users' - code which presents functionality to userspace.
+ obj-$(CONFIG_MTD_CHAR)		+= mtdchar.o

target/linux/adm5120/patches-3.8/120-rb153_cf_driver.patch

@@ -0,0 +1,28 @@
+--- a/drivers/ata/Makefile
++++ b/drivers/ata/Makefile
+@@ -90,6 +90,7 @@ obj-$(CONFIG_PATA_PCMCIA)	+= pata_pcmcia
+ obj-$(CONFIG_PATA_PALMLD)	+= pata_palmld.o
+ obj-$(CONFIG_PATA_PLATFORM)	+= pata_platform.o
+ obj-$(CONFIG_PATA_OF_PLATFORM)	+= pata_of_platform.o
++obj-$(CONFIG_PATA_RB153_CF)	+= pata_rb153_cf.o
+ obj-$(CONFIG_PATA_RB532)	+= pata_rb532_cf.o
+ obj-$(CONFIG_PATA_RZ1000)	+= pata_rz1000.o
+ obj-$(CONFIG_PATA_SAMSUNG_CF)	+= pata_samsung_cf.o
+--- a/drivers/ata/Kconfig
++++ b/drivers/ata/Kconfig
+@@ -852,6 +852,15 @@ config PATA_QDI
+ 	help
+ 	  Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
+ 
++config PATA_RB153_CF
++	tristate "RouterBOARD 153 Compact Flash support"
++	depends on ADM5120_MACH_RB_153
++	help
++	  This option enables support for a Compact Flash connected on
++	  the RouterBOARD 153.
++
++	  If unsure, say N.
++
+ config PATA_RB532
+ 	tristate "RouterBoard 532 PATA CompactFlash support"
+ 	depends on MIKROTIK_RB532

target/linux/adm5120/patches-3.8/200-amba_pl010_hacks.patch

@@ -0,0 +1,355 @@
+--- a/drivers/tty/serial/amba-pl010.c
++++ b/drivers/tty/serial/amba-pl010.c
+@@ -49,11 +49,9 @@
+ 
+ #include <asm/io.h>
+ 
+-#define UART_NR		8
+-
+ #define SERIAL_AMBA_MAJOR	204
+ #define SERIAL_AMBA_MINOR	16
+-#define SERIAL_AMBA_NR		UART_NR
++#define SERIAL_AMBA_NR		CONFIG_SERIAL_AMBA_PL010_NUMPORTS
+ 
+ #define AMBA_ISR_PASS_LIMIT	256
+ 
+@@ -79,9 +77,9 @@ static void pl010_stop_tx(struct uart_po
+ 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ 	unsigned int cr;
+ 
+-	cr = readb(uap->port.membase + UART010_CR);
++	cr = __raw_readl(uap->port.membase + UART010_CR);
+ 	cr &= ~UART010_CR_TIE;
+-	writel(cr, uap->port.membase + UART010_CR);
++	__raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ 
+ static void pl010_start_tx(struct uart_port *port)
+@@ -89,9 +87,9 @@ static void pl010_start_tx(struct uart_p
+ 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ 	unsigned int cr;
+ 
+-	cr = readb(uap->port.membase + UART010_CR);
++	cr = __raw_readl(uap->port.membase + UART010_CR);
+ 	cr |= UART010_CR_TIE;
+-	writel(cr, uap->port.membase + UART010_CR);
++	__raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ 
+ static void pl010_stop_rx(struct uart_port *port)
+@@ -99,9 +97,9 @@ static void pl010_stop_rx(struct uart_po
+ 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ 	unsigned int cr;
+ 
+-	cr = readb(uap->port.membase + UART010_CR);
++	cr = __raw_readl(uap->port.membase + UART010_CR);
+ 	cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
+-	writel(cr, uap->port.membase + UART010_CR);
++	__raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ 
+ static void pl010_enable_ms(struct uart_port *port)
+@@ -109,9 +107,9 @@ static void pl010_enable_ms(struct uart_
+ 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ 	unsigned int cr;
+ 
+-	cr = readb(uap->port.membase + UART010_CR);
++	cr = __raw_readl(uap->port.membase + UART010_CR);
+ 	cr |= UART010_CR_MSIE;
+-	writel(cr, uap->port.membase + UART010_CR);
++	__raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+ 
+ static void pl010_rx_chars(struct uart_amba_port *uap)
+@@ -119,9 +117,9 @@ static void pl010_rx_chars(struct uart_a
+ 	struct tty_struct *tty = uap->port.state->port.tty;
+ 	unsigned int status, ch, flag, rsr, max_count = 256;
+ 
+-	status = readb(uap->port.membase + UART01x_FR);
++	status = __raw_readl(uap->port.membase + UART01x_FR);
+ 	while (UART_RX_DATA(status) && max_count--) {
+-		ch = readb(uap->port.membase + UART01x_DR);
++		ch = __raw_readl(uap->port.membase + UART01x_DR);
+ 		flag = TTY_NORMAL;
+ 
+ 		uap->port.icount.rx++;
+@@ -130,9 +128,9 @@ static void pl010_rx_chars(struct uart_a
+ 		 * Note that the error handling code is
+ 		 * out of the main execution path
+ 		 */
+-		rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
++		rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+ 		if (unlikely(rsr & UART01x_RSR_ANY)) {
+-			writel(0, uap->port.membase + UART01x_ECR);
++			__raw_writel(0, uap->port.membase + UART01x_ECR);
+ 
+ 			if (rsr & UART01x_RSR_BE) {
+ 				rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
+@@ -162,7 +160,7 @@ static void pl010_rx_chars(struct uart_a
+ 		uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
+ 
+ 	ignore_char:
+-		status = readb(uap->port.membase + UART01x_FR);
++		status = __raw_readl(uap->port.membase + UART01x_FR);
+ 	}
+ 	spin_unlock(&uap->port.lock);
+ 	tty_flip_buffer_push(tty);
+@@ -175,7 +173,7 @@ static void pl010_tx_chars(struct uart_a
+ 	int count;
+ 
+ 	if (uap->port.x_char) {
+-		writel(uap->port.x_char, uap->port.membase + UART01x_DR);
++		__raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
+ 		uap->port.icount.tx++;
+ 		uap->port.x_char = 0;
+ 		return;
+@@ -187,7 +185,7 @@ static void pl010_tx_chars(struct uart_a
+ 
+ 	count = uap->port.fifosize >> 1;
+ 	do {
+-		writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
++		__raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
+ 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ 		uap->port.icount.tx++;
+ 		if (uart_circ_empty(xmit))
+@@ -205,9 +203,9 @@ static void pl010_modem_status(struct ua
+ {
+ 	unsigned int status, delta;
+ 
+-	writel(0, uap->port.membase + UART010_ICR);
++	__raw_writel(0, uap->port.membase + UART010_ICR);
+ 
+-	status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++	status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+ 
+ 	delta = status ^ uap->old_status;
+ 	uap->old_status = status;
+@@ -235,7 +233,7 @@ static irqreturn_t pl010_int(int irq, vo
+ 
+ 	spin_lock(&uap->port.lock);
+ 
+-	status = readb(uap->port.membase + UART010_IIR);
++	status = __raw_readl(uap->port.membase + UART010_IIR);
+ 	if (status) {
+ 		do {
+ 			if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
+@@ -248,7 +246,7 @@ static irqreturn_t pl010_int(int irq, vo
+ 			if (pass_counter-- == 0)
+ 				break;
+ 
+-			status = readb(uap->port.membase + UART010_IIR);
++			status = __raw_readl(uap->port.membase + UART010_IIR);
+ 		} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
+ 				   UART010_IIR_TIS));
+ 		handled = 1;
+@@ -262,7 +260,7 @@ static irqreturn_t pl010_int(int irq, vo
+ static unsigned int pl010_tx_empty(struct uart_port *port)
+ {
+ 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+-	unsigned int status = readb(uap->port.membase + UART01x_FR);
++	unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
+ 	return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+ }
+ 
+@@ -272,7 +270,7 @@ static unsigned int pl010_get_mctrl(stru
+ 	unsigned int result = 0;
+ 	unsigned int status;
+ 
+-	status = readb(uap->port.membase + UART01x_FR);
++	status = __raw_readl(uap->port.membase + UART01x_FR);
+ 	if (status & UART01x_FR_DCD)
+ 		result |= TIOCM_CAR;
+ 	if (status & UART01x_FR_DSR)
+@@ -298,12 +296,12 @@ static void pl010_break_ctl(struct uart_
+ 	unsigned int lcr_h;
+ 
+ 	spin_lock_irqsave(&uap->port.lock, flags);
+-	lcr_h = readb(uap->port.membase + UART010_LCRH);
++	lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
+ 	if (break_state == -1)
+ 		lcr_h |= UART01x_LCRH_BRK;
+ 	else
+ 		lcr_h &= ~UART01x_LCRH_BRK;
+-	writel(lcr_h, uap->port.membase + UART010_LCRH);
++	__raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
+ 	spin_unlock_irqrestore(&uap->port.lock, flags);
+ }
+ 
+@@ -331,12 +329,12 @@ static int pl010_startup(struct uart_por
+ 	/*
+ 	 * initialise the old status of the modem signals
+ 	 */
+-	uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++	uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+ 
+ 	/*
+ 	 * Finally, enable interrupts
+ 	 */
+-	writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
++	__raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
+ 	       uap->port.membase + UART010_CR);
+ 
+ 	return 0;
+@@ -359,10 +357,10 @@ static void pl010_shutdown(struct uart_p
+ 	/*
+ 	 * disable all interrupts, disable the port
+ 	 */
+-	writel(0, uap->port.membase + UART010_CR);
++	__raw_writel(0, uap->port.membase + UART010_CR);
+ 
+ 	/* disable break condition and fifos */
+-	writel(readb(uap->port.membase + UART010_LCRH) &
++	__raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
+ 		~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
+ 	       uap->port.membase + UART010_LCRH);
+ 
+@@ -384,7 +382,7 @@ pl010_set_termios(struct uart_port *port
+ 	/*
+ 	 * Ask the core to calculate the divisor for us.
+ 	 */
+-	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 
++	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
+ 	quot = uart_get_divisor(port, baud);
+ 
+ 	switch (termios->c_cflag & CSIZE) {
+@@ -447,25 +445,25 @@ pl010_set_termios(struct uart_port *port
+ 		uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
+ 
+ 	/* first, disable everything */
+-	old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
++	old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
+ 
+ 	if (UART_ENABLE_MS(port, termios->c_cflag))
+ 		old_cr |= UART010_CR_MSIE;
+ 
+-	writel(0, uap->port.membase + UART010_CR);
++	__raw_writel(0, uap->port.membase + UART010_CR);
+ 
+ 	/* Set baud rate */
+ 	quot -= 1;
+-	writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
+-	writel(quot & 0xff, uap->port.membase + UART010_LCRL);
++	__raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
++	__raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
+ 
+ 	/*
+ 	 * ----------v----------v----------v----------v-----
+ 	 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
+ 	 * ----------^----------^----------^----------^-----
+ 	 */
+-	writel(lcr_h, uap->port.membase + UART010_LCRH);
+-	writel(old_cr, uap->port.membase + UART010_CR);
++	__raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
++	__raw_writel(old_cr, uap->port.membase + UART010_CR);
+ 
+ 	spin_unlock_irqrestore(&uap->port.lock, flags);
+ }
+@@ -547,7 +545,7 @@ static struct uart_ops amba_pl010_pops =
+ 	.verify_port	= pl010_verify_port,
+ };
+ 
+-static struct uart_amba_port *amba_ports[UART_NR];
++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
+ 
+ #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
+ 
+@@ -557,10 +555,10 @@ static void pl010_console_putchar(struct
+ 	unsigned int status;
+ 
+ 	do {
+-		status = readb(uap->port.membase + UART01x_FR);
++		status = __raw_readl(uap->port.membase + UART01x_FR);
+ 		barrier();
+ 	} while (!UART_TX_READY(status));
+-	writel(ch, uap->port.membase + UART01x_DR);
++	__raw_writel(ch, uap->port.membase + UART01x_DR);
+ }
+ 
+ static void
+@@ -574,8 +572,8 @@ pl010_console_write(struct console *co,
+ 	/*
+ 	 *	First save the CR then disable the interrupts
+ 	 */
+-	old_cr = readb(uap->port.membase + UART010_CR);
+-	writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
++	old_cr = __raw_readl(uap->port.membase + UART010_CR);
++	__raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
+ 
+ 	uart_console_write(&uap->port, s, count, pl010_console_putchar);
+ 
+@@ -584,10 +582,10 @@ pl010_console_write(struct console *co,
+ 	 *	and restore the TCR
+ 	 */
+ 	do {
+-		status = readb(uap->port.membase + UART01x_FR);
++		status = __raw_readl(uap->port.membase + UART01x_FR);
+ 		barrier();
+ 	} while (status & UART01x_FR_BUSY);
+-	writel(old_cr, uap->port.membase + UART010_CR);
++	__raw_writel(old_cr, uap->port.membase + UART010_CR);
+ 
+ 	clk_disable(uap->clk);
+ }
+@@ -596,9 +594,9 @@ static void __init
+ pl010_console_get_options(struct uart_amba_port *uap, int *baud,
+ 			     int *parity, int *bits)
+ {
+-	if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
++	if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
+ 		unsigned int lcr_h, quot;
+-		lcr_h = readb(uap->port.membase + UART010_LCRH);
++		lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
+ 
+ 		*parity = 'n';
+ 		if (lcr_h & UART01x_LCRH_PEN) {
+@@ -613,8 +611,8 @@ pl010_console_get_options(struct uart_am
+ 		else
+ 			*bits = 8;
+ 
+-		quot = readb(uap->port.membase + UART010_LCRL) |
+-		       readb(uap->port.membase + UART010_LCRM) << 8;
++		quot = __raw_readl(uap->port.membase + UART010_LCRL) |
++		       __raw_readl(uap->port.membase + UART010_LCRM) << 8;
+ 		*baud = uap->port.uartclk / (16 * (quot + 1));
+ 	}
+ }
+@@ -633,7 +631,7 @@ static int __init pl010_console_setup(st
+ 	 * if so, search for the first available port that does have
+ 	 * console support.
+ 	 */
+-	if (co->index >= UART_NR)
++	if (co->index >= SERIAL_AMBA_NR)
+ 		co->index = 0;
+ 	uap = amba_ports[co->index];
+ 	if (!uap)
+@@ -675,7 +673,7 @@ static struct uart_driver amba_reg = {
+ 	.dev_name		= "ttyAM",
+ 	.major			= SERIAL_AMBA_MAJOR,
+ 	.minor			= SERIAL_AMBA_MINOR,
+-	.nr			= UART_NR,
++	.nr			= SERIAL_AMBA_NR,
+ 	.cons			= AMBA_CONSOLE,
+ };
+ 
+--- a/drivers/tty/serial/Kconfig
++++ b/drivers/tty/serial/Kconfig
+@@ -16,10 +16,18 @@ config SERIAL_AMBA_PL010
+ 	help
+ 	  This selects the ARM(R) AMBA(R) PrimeCell PL010 UART.  If you have
+ 	  an Integrator/AP or Integrator/PP2 platform, or if you have a
+-	  Cirrus Logic EP93xx CPU, say Y or M here.
++	  Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
+ 
+ 	  If unsure, say N.
+ 
++config SERIAL_AMBA_PL010_NUMPORTS
++	int "Maximum number of AMBA PL010 serial ports"
++	depends on SERIAL_AMBA_PL010
++	default "8"
++	---help---
++	  Set this to the number of serial ports you want the AMBA PL010 driver
++	  to support.
++
+ config SERIAL_AMBA_PL010_CONSOLE
+ 	bool "Support for console on AMBA serial port"
+ 	depends on SERIAL_AMBA_PL010=y

target/linux/adm5120/patches-3.8/203-gpio_leds_brightness.patch

@@ -0,0 +1,27 @@
+--- a/drivers/leds/leds-gpio.c
++++ b/drivers/leds/leds-gpio.c
+@@ -56,13 +56,17 @@ static void gpio_led_set(struct led_clas
+ 		container_of(led_cdev, struct gpio_led_data, cdev);
+ 	int level;
+ 
+-	if (value == LED_OFF)
+-		level = 0;
+-	else
+-		level = 1;
+-
+-	if (led_dat->active_low)
+-		level = !level;
++	switch (value) {
++	case LED_OFF:
++		level = led_dat->active_low ? 1 : 0;
++		break;
++	case LED_FULL:
++		level = led_dat->active_low ? 0 : 1;
++		break;
++	default:
++		level = value;
++		break;
++	}
+ 
+ 	/* Setting GPIOs with I2C/etc requires a task context, and we don't
+ 	 * seem to have a reliable way to know if we're already in one; so

target/linux/adm5120/patches-3.8/310-adm5120_wdt.patch

@@ -0,0 +1,31 @@
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -984,6 +984,18 @@ config RC32434_WDT
+ 	  To compile this driver as a module, choose M here: the
+ 	  module will be called rc32434_wdt.
+ 
++config ADM5120_WDT
++	tristate "Infineon ADM5120 SoC hardware watchdog"
++	depends on WATCHDOG && ADM5120
++	help
++	  This is a driver for hardware watchdog integrated in Infineon
++	  ADM5120 SoC. This watchdog simply watches your kernel to make sure
++	  it doesn't freeze, and if it does, it reboots your computer after a
++	  certain amount of time.
++
++	  To compile this driver as a module, choose M here: the module will be
++	  called adm5120_wdt.
++
+ config INDYDOG
+ 	tristate "Indy/I2 Hardware Watchdog"
+ 	depends on SGI_HAS_INDYDOG
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -122,6 +122,7 @@ obj-$(CONFIG_ATH79_WDT) += ath79_wdt.o
+ obj-$(CONFIG_BCM47XX_WDT) += bcm47xx_wdt.o
+ obj-$(CONFIG_BCM63XX_WDT) += bcm63xx_wdt.o
+ obj-$(CONFIG_RC32434_WDT) += rc32434_wdt.o
++obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
+ obj-$(CONFIG_INDYDOG) += indydog.o
+ obj-$(CONFIG_JZ4740_WDT) += jz4740_wdt.o
+ obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o

target/linux/adm5120/rb1xx/config-3.8

@@ -0,0 +1,54 @@
+# CONFIG_ADM5120_MACH_5GXI is not set
+# CONFIG_ADM5120_MACH_BR_6104K is not set
+# CONFIG_ADM5120_MACH_BR_6104KP is not set
+# CONFIG_ADM5120_MACH_BR_61X4WG is not set
+# CONFIG_ADM5120_MACH_CAS_771 is not set
+# CONFIG_ADM5120_MACH_EASY5120P_ATA is not set
+# CONFIG_ADM5120_MACH_EASY5120_RT is not set
+# CONFIG_ADM5120_MACH_EASY5120_WVOIP is not set
+# CONFIG_ADM5120_MACH_EASY83000 is not set
+# CONFIG_ADM5120_MACH_EB_214A is not set
+# CONFIG_ADM5120_MACH_NFS_101 is not set
+# CONFIG_ADM5120_MACH_NP27G is not set
+# CONFIG_ADM5120_MACH_NP28G is not set
+# CONFIG_ADM5120_MACH_PMUGW is not set
+CONFIG_ADM5120_MACH_RB_11X=y
+CONFIG_ADM5120_MACH_RB_133=y
+CONFIG_ADM5120_MACH_RB_133C=y
+CONFIG_ADM5120_MACH_RB_150=y
+CONFIG_ADM5120_MACH_RB_153=y
+CONFIG_ADM5120_MACH_RB_192=y
+# CONFIG_ADM5120_MACH_WP54 is not set
+# CONFIG_ADM5120_OEM_CELLVISION is not set
+# CONFIG_ADM5120_OEM_COMPEX is not set
+# CONFIG_ADM5120_OEM_EDIMAX is not set
+# CONFIG_ADM5120_OEM_GENERIC is not set
+# CONFIG_ADM5120_OEM_INFINEON is not set
+CONFIG_ADM5120_OEM_MIKROTIK=y
+# CONFIG_ADM5120_OEM_MOTOROLA is not set
+# CONFIG_ADM5120_OEM_OSBRIDGE is not set
+CONFIG_CMDLINE="console=ttyAM0,115200 rootfstype=yaffs2"
+# CONFIG_JFFS2_FS is not set
+# CONFIG_MTD_MYLOADER_PARTS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_PLATFORM=y
+# CONFIG_MTD_ROOTFS_SPLIT is not set
+# CONFIG_MTD_SM_COMMON is not set
+# CONFIG_MTD_TRXSPLIT is not set
+# CONFIG_OVERLAYFS_FS is not set
+# CONFIG_PATA_RB153_CF is not set
+# CONFIG_SQUASHFS is not set
+CONFIG_YAFFS_9BYTE_TAGS=y
+# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
+CONFIG_YAFFS_AUTO_YAFFS2=y
+# CONFIG_YAFFS_DISABLE_BACKGROUND is not set
+# CONFIG_YAFFS_DISABLE_BLOCK_REFRESHING is not set
+CONFIG_YAFFS_DISABLE_TAGS_ECC=y
+# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
+# CONFIG_YAFFS_EMPTY_LOST_AND_FOUND is not set
+CONFIG_YAFFS_FS=y
+CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
+CONFIG_YAFFS_XATTR=y
+CONFIG_YAFFS_YAFFS1=y
+CONFIG_YAFFS_YAFFS2=y

target/linux/adm5120/router_be/config-3.8

@@ -0,0 +1,13 @@
+CONFIG_ADM5120_MACH_P_334WT=y
+CONFIG_ADM5120_MACH_P_335=y
+# CONFIG_ADM5120_OEM_CELLVISION is not set
+# CONFIG_ADM5120_OEM_COMPEX is not set
+# CONFIG_ADM5120_OEM_EDIMAX is not set
+# CONFIG_ADM5120_OEM_GENERIC is not set
+# CONFIG_ADM5120_OEM_INFINEON is not set
+# CONFIG_ADM5120_OEM_MOTOROLA is not set
+# CONFIG_ADM5120_OEM_OSBRIDGE is not set
+CONFIG_ADM5120_OEM_ZYXEL=y
+CONFIG_CPU_BIG_ENDIAN=y
+# CONFIG_CPU_LITTLE_ENDIAN is not set
+CONFIG_SWAP_IO_SPACE=y