KumiSystems/openwrtv3
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv3/target/linux/ar71xx/patches-4.9/701-MIPS-ath79-add-routerboard-detection.patch

32 lines
1.1 KiB
Diff
Raw Normal View History

ar71xx: Add kernel 4.9 support This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-03 16:02:59 +00:00
--- a/arch/mips/ath79/prom.c
+++ b/arch/mips/ath79/prom.c
ar71xx: complete support for RB wAP 2nD This patch adds support for the MikroTik RouterBOARD wAP https://mikrotik.com/product/RBwAP2nD Specifications: - SoC: Qualcomm QCA9533 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9533, 2x2:2 - Ethernet: 1x100M (802.3af/at POE in) This patch adds missing code to fully support wAP. Machfile already contained configuration for wAP 2nD but device specific configuration like LEDs etc. was missing. Installation: 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-28 10:30:39 +00:00
@@ -136,6 +136,28 @@ void __init prom_init(void)
ar71xx: Add kernel 4.9 support This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-03 16:02:59 +00:00
initrd_end = initrd_start + fw_getenvl("initrd_size");
}
#endif
+
+ if (strstr(arcs_cmdline, "board=750Gr3") ||
+ strstr(arcs_cmdline, "board=750i") ||
+ strstr(arcs_cmdline, "board=750-hb") ||
+ strstr(arcs_cmdline, "board=411") ||
+ strstr(arcs_cmdline, "board=433") ||
+ strstr(arcs_cmdline, "board=435") ||
+ strstr(arcs_cmdline, "board=450") ||
+ strstr(arcs_cmdline, "board=493") ||
+ strstr(arcs_cmdline, "board=951G") ||
+ strstr(arcs_cmdline, "board=H951L") ||
+ strstr(arcs_cmdline, "board=952-hb") ||
+ strstr(arcs_cmdline, "board=953gs") ||
+ strstr(arcs_cmdline, "board=962") ||
+ strstr(arcs_cmdline, "board=lhg") ||
+ strstr(arcs_cmdline, "board=map-hb") ||
ar71xx: complete support for RB wAP 2nD This patch adds support for the MikroTik RouterBOARD wAP https://mikrotik.com/product/RBwAP2nD Specifications: - SoC: Qualcomm QCA9533 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9533, 2x2:2 - Ethernet: 1x100M (802.3af/at POE in) This patch adds missing code to fully support wAP. Machfile already contained configuration for wAP 2nD but device specific configuration like LEDs etc. was missing. Installation: 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-28 10:30:39 +00:00
+ strstr(arcs_cmdline, "board=wap-hb") ||
ar71xx: Add kernel 4.9 support This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-03 16:02:59 +00:00
+ strstr(arcs_cmdline, "board=2011L") ||
+ strstr(arcs_cmdline, "board=2011r") ||
+ strstr(arcs_cmdline, "board=711Gr100") ||
+ strstr(arcs_cmdline, "board=922gs"))
+ ath79_prom_append_cmdline("console", "ttyS0,115200");
}
void __init prom_free_prom_memory(void)
Reference in a new issue Copy permalink