openwrtv3/target/linux/at91/patches/100-at91_i2c.patch

--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -283,7 +283,7 @@ comment "I2C system bus drivers (mostly
 
 config I2C_AT91
 	tristate "Atmel AT91 I2C Two-Wire interface (TWI)"
-	depends on ARCH_AT91 && EXPERIMENTAL && BROKEN
+	depends on ARCH_AT91 && EXPERIMENTAL
 	help
 	  This supports the use of the I2C interface on Atmel AT91
 	  processors.
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -11,8 +11,18 @@
     it under the terms of the GNU General Public License as published by
     the Free Software Foundation; either version 2 of the License, or
     (at your option) any later version.
+
+    D. Gilbert [20100318 AT91SAM9G20]
+	- Check for NACK, a NACK will abort current tranfser,
+          returned as errno=EREMOTEIO unless I2C_M_IGNORE_NAK is set
+        - Only supports 7 bit I2C device (slave) address
+	- clockrate adjustable (module_param).
 */
 
+
+/* Uncomment following line to see dev_dbg() output in logs */
+/* #define DEBUG 1 */
+
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/err.h>
@@ -32,26 +42,28 @@
 #define TWI_CLOCK		100000		/* Hz. max 400 Kbits/sec */
 
 
+static unsigned int clockrate = TWI_CLOCK;
+static unsigned int prev_clockrate = TWI_CLOCK;
 static struct clk *twi_clk;
 static void __iomem *twi_base;
 
 #define at91_twi_read(reg)		__raw_readl(twi_base + (reg))
 #define at91_twi_write(reg, val)	__raw_writel((val), twi_base + (reg))
 
-
 /*
- * Initialize the TWI hardware registers.
+ * Set TWI clock dividers based on clockrate (clock rate for SCL)
  */
-static void __devinit at91_twi_hwinit(void)
+static void at91_twi_clock_dividers(void)
 {
 	unsigned long cdiv, ckdiv;
 
-	at91_twi_write(AT91_TWI_IDR, 0xffffffff);	/* Disable all interrupts */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_SWRST);	/* Reset peripheral */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN);	/* Set Master mode */
+	if (clockrate < 1000)
+		clockrate = 1000;	
+	else if (clockrate > 400000)
+		clockrate = 400000;	
 
-	/* Calcuate clock dividers */
-	cdiv = (clk_get_rate(twi_clk) / (2 * TWI_CLOCK)) - 3;
+	/* Calculate clock dividers */
+	cdiv = (clk_get_rate(twi_clk) / (2 * clockrate)) - 3;
 	cdiv = cdiv + 1;	/* round up */
 	ckdiv = 0;
 	while (cdiv > 255) {
@@ -61,41 +73,92 @@ static void __devinit at91_twi_hwinit(vo
 
 	if (cpu_is_at91rm9200()) {			/* AT91RM9200 Errata #22 */
 		if (ckdiv > 5) {
-			printk(KERN_ERR "AT91 I2C: Invalid TWI_CLOCK value!\n");
+			printk(KERN_ERR "i2c-at91: Invalid AT91RM9200 clock rate\n");
 			ckdiv = 5;
 		}
 	}
+	/* AT91SAM9G20 has 3 bits for ckdiv so it cannot exceed 7 */
+	if (cpu_is_at91sam9g20()) {
+		if (ckdiv > 7) {
+			printk(KERN_ERR "i2c-at91: Invalid AT91SAM9G20 clock "
+			       "rate, ckdiv=%lu\n", ckdiv);
+			ckdiv = 7;
+		}
+	}
 
 	at91_twi_write(AT91_TWI_CWGR, (ckdiv << 16) | (cdiv << 8) | cdiv);
+	prev_clockrate = clockrate;
 }
 
 /*
- * Poll the i2c status register until the specified bit is set.
- * Returns 0 if timed out (100 msec).
+ * Initialize the TWI hardware registers.
  */
-static short at91_poll_status(unsigned long bit)
+static void __devinit at91_twi_hwinit(void)
 {
-	int loop_cntr = 10000;
+	at91_twi_write(AT91_TWI_IDR, 0xffffffff);  /* Disable all interrupts */
+	at91_twi_write(AT91_TWI_CR, AT91_TWI_SWRST);     /* Reset peripheral */
+	/* Set Master mode; Atmel suggests disabling slave mode */
+	at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN | AT91_TWI_SVDIS);
 
+	at91_twi_clock_dividers();
+}
+
+/*
+ * Poll the i2c status register until the specified bit is set or a NACK
+ * occurs. Returns 0 if timed out (50 msec). If nack_seen_p is non-NULL
+ * then write 0 to it first, then if the NACK bit is set in the status
+ * register then write 1 to it and immediately return with a value of 1.
+ */
+static short at91_poll_status(unsigned long bit, int * nack_seen_p)
+{
+	int loop_cntr = 5000;
+	unsigned long stat;
+
+	if (nack_seen_p)
+		*nack_seen_p = 0;
+	if (clockrate <= 20000)
+		loop_cntr = 100;
 	do {
-		udelay(10);
-	} while (!(at91_twi_read(AT91_TWI_SR) & bit) && (--loop_cntr > 0));
+		if (clockrate <= 20000)
+			udelay(100);
+		else if (clockrate <= 100000)
+			udelay(10);
+		else
+			udelay(3);
+		stat = at91_twi_read(AT91_TWI_SR);
+		if ((stat & AT91_TWI_NACK) && nack_seen_p) {
+			*nack_seen_p = 1;
+			return 1;
+		}
+	} while (!(stat & bit) && (--loop_cntr > 0));
 
 	return (loop_cntr > 0);
 }
 
 static int xfer_read(struct i2c_adapter *adap, unsigned char *buf, int length)
 {
+	int nack_seen = 0;
+	int sent_stop = 0;
+
 	/* Send Start */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_START);
+	if (1 == length) {
+	    at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
+	    sent_stop = 1;
+	} else
+	    at91_twi_write(AT91_TWI_CR, AT91_TWI_START);
 
 	/* Read data */
 	while (length--) {
-		if (!length)	/* need to send Stop before reading last byte */
+		/* send Stop before reading last byte (if not already done) */
+		if ((0 == length) && (0 == sent_stop))
 			at91_twi_write(AT91_TWI_CR, AT91_TWI_STOP);
-		if (!at91_poll_status(AT91_TWI_RXRDY)) {
+		if (!at91_poll_status(AT91_TWI_RXRDY, &nack_seen)) {
 			dev_dbg(&adap->dev, "RXRDY timeout\n");
 			return -ETIMEDOUT;
+		} else if (nack_seen) {
+			dev_dbg(&adap->dev, "read NACKed\n");
+			/* NACK supplies Stop */
+			return -EREMOTEIO;
 		}
 		*buf++ = (at91_twi_read(AT91_TWI_RHR) & 0xff);
 	}
@@ -105,16 +168,24 @@ static int xfer_read(struct i2c_adapter
 
 static int xfer_write(struct i2c_adapter *adap, unsigned char *buf, int length)
 {
+	int nack_seen = 0;
+
 	/* Load first byte into transmitter */
 	at91_twi_write(AT91_TWI_THR, *buf++);
 
-	/* Send Start */
+	/* Send Start [AT91SAM9G20 does not need this on write] */
 	at91_twi_write(AT91_TWI_CR, AT91_TWI_START);
 
 	do {
-		if (!at91_poll_status(AT91_TWI_TXRDY)) {
+		if (!at91_poll_status(AT91_TWI_TXRDY, &nack_seen)) {
 			dev_dbg(&adap->dev, "TXRDY timeout\n");
+			/* Set Master mode again */
+			at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN);
 			return -ETIMEDOUT;
+		} else if (nack_seen) {
+			dev_dbg(&adap->dev, "write NACKed\n");
+			/* NACK supplies Stop */
+			return -EREMOTEIO;
 		}
 
 		length--;	/* byte was transmitted */
@@ -123,7 +194,7 @@ static int xfer_write(struct i2c_adapter
 			at91_twi_write(AT91_TWI_THR, *buf++);
 	} while (length);
 
-	/* Send Stop */
+	/* Send Stop [AT91SAM9G20 does not need this on write] */
 	at91_twi_write(AT91_TWI_CR, AT91_TWI_STOP);
 
 	return 0;
@@ -136,11 +207,19 @@ static int xfer_write(struct i2c_adapter
  * Instead the "internal device address" has to be written using a separate
  * i2c message.
  * http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2004-September/024411.html
+ * [dpg] By 2010 silicon bugs should be fixed, will need IADR for 10 bit device address
  */
 static int at91_xfer(struct i2c_adapter *adap, struct i2c_msg *pmsg, int num)
 {
 	int i, ret;
+	int nack_seen = 0;
 
+	if (prev_clockrate != clockrate) {
+		dev_dbg(&adap->dev, "at91_xfer: prev_clockrate=%u "
+			"clockrate=%u, change\n", prev_clockrate, clockrate);
+		at91_twi_clock_dividers();
+		msleep(1);	/* let things settle */
+	}
 	dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);
 
 	for (i = 0; i < num; i++) {
@@ -158,13 +237,23 @@ static int at91_xfer(struct i2c_adapter
 			else
 				ret = xfer_write(adap, pmsg->buf, pmsg->len);
 
-			if (ret)
-				return ret;
-
+			if (ret) {
+				if ((I2C_M_IGNORE_NAK & pmsg->flags) &&
+				    (-EREMOTEIO == ret)) {
+					dev_dbg(&adap->dev, "transfer "
+						"NACKed, skip to next\n");
+					pmsg++;
+					continue;
+				} else
+					return ret;
+			}
 			/* Wait until transfer is finished */
-			if (!at91_poll_status(AT91_TWI_TXCOMP)) {
+			if (!at91_poll_status(AT91_TWI_TXCOMP, &nack_seen)) {
 				dev_dbg(&adap->dev, "TXCOMP timeout\n");
 				return -ETIMEDOUT;
+			} else if (nack_seen) {
+				dev_dbg(&adap->dev, "TXCOMP NACKed\n");
+				return -EREMOTEIO;
 			}
 		}
 		dev_dbg(&adap->dev, "transfer complete\n");
@@ -239,7 +328,8 @@ static int __devinit at91_i2c_probe(stru
 		goto fail3;
 	}
 
-	dev_info(&pdev->dev, "AT91 i2c bus driver.\n");
+	dev_info(&pdev->dev, "AT91 TWI (I2C) bus driver [SCL %d Hz]\n",
+		 clockrate);
 	return 0;
 
 fail3:
@@ -295,6 +385,11 @@ static int at91_i2c_resume(struct platfo
 #define at91_i2c_resume		NULL
 #endif
 
+/* I2C clock speed, in Hz 0-400kHz*/
+module_param(clockrate, uint,  S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(clockrate,
+		 "SCL clock rate, 1000 to 400000 Hz (def: 100 kHz)");
+
 /* work with "modprobe at91_i2c" from hotplugging or coldplugging */
 MODULE_ALIAS("platform:at91_i2c");
 
@@ -323,5 +418,5 @@ module_init(at91_i2c_init);
 module_exit(at91_i2c_exit);
 
 MODULE_AUTHOR("Rick Bronson");
-MODULE_DESCRIPTION("I2C (TWI) driver for Atmel AT91");
+MODULE_DESCRIPTION("I2C (TWI) master driver for Atmel AT91");
 MODULE_LICENSE("GPL");