KumiSystems/openwrtv3
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv3/target/linux/ipq40xx/config-4.14

492 lines
12 KiB
Text
Raw Normal View History

ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
CONFIG_ALIGNMENT_TRAP=y
# CONFIG_APQ_GCC_8084 is not set
# CONFIG_APQ_MMCC_8084 is not set
CONFIG_AR40XX_PHY=y
CONFIG_ARCH_CLOCKSOURCE_DATA=y
CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
CONFIG_ARCH_HAS_SET_MEMORY=y
CONFIG_ARCH_HAS_SG_CHAIN=y
CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
CONFIG_ARCH_HAS_TICK_BROADCAST=y
CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_IPQ40XX=y
# CONFIG_ARCH_MDM9615 is not set
CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
# CONFIG_ARCH_MSM8960 is not set
# CONFIG_ARCH_MSM8974 is not set
# CONFIG_ARCH_MSM8X60 is not set
CONFIG_ARCH_MULTIPLATFORM=y
# CONFIG_ARCH_MULTI_CPU_AUTO is not set
CONFIG_ARCH_MULTI_V6_V7=y
CONFIG_ARCH_MULTI_V7=y
CONFIG_ARCH_NR_GPIO=0
CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
CONFIG_ARCH_QCOM=y
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
CONFIG_ARCH_SUPPORTS_UPROBES=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARCH_USE_BUILTIN_BSWAP=y
CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
# CONFIG_ARCH_WANTS_THP_SWAP is not set
CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_ARM=y
CONFIG_ARM_AMBA=y
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ARCH_TIMER=y
CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
# CONFIG_ARM_ATAG_DTB_COMPAT is not set
CONFIG_ARM_CPUIDLE=y
CONFIG_ARM_CPU_SUSPEND=y
# CONFIG_ARM_CPU_TOPOLOGY is not set
CONFIG_ARM_GIC=y
CONFIG_ARM_HAS_SG_CHAIN=y
CONFIG_ARM_L1_CACHE_SHIFT=6
CONFIG_ARM_L1_CACHE_SHIFT_6=y
# CONFIG_ARM_LPAE is not set
CONFIG_ARM_PATCH_IDIV=y
CONFIG_ARM_PATCH_PHYS_VIRT=y
CONFIG_ARM_QCOM_CPUIDLE=y
# CONFIG_ARM_SMMU is not set
# CONFIG_ARM_SP805_WATCHDOG is not set
CONFIG_ARM_THUMB=y
# CONFIG_ARM_THUMBEE is not set
CONFIG_ARM_UNWIND=y
CONFIG_ARM_VIRT_EXT=y
CONFIG_AT803X_PHY=y
CONFIG_AUTO_ZRELADDR=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_MQ_PCI=y
CONFIG_BOUNCE=y
CONFIG_BUS_TOPOLOGY_ADHOC=y
# CONFIG_CACHE_L2X0 is not set
CONFIG_CLKDEV_LOOKUP=y
CONFIG_CLKSRC_QCOM=y
CONFIG_CLONE_BACKWARDS=y
CONFIG_COMMON_CLK=y
CONFIG_COMMON_CLK_QCOM=y
CONFIG_CPUFREQ_DT=y
CONFIG_CPUFREQ_DT_PLATDEV=y
CONFIG_CPU_32v6K=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
# CONFIG_CPU_BIG_ENDIAN is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
CONFIG_CPU_CACHE_V7=y
CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_GOV_ATTR_SET=y
CONFIG_CPU_FREQ_GOV_COMMON=y
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_STAT=y
CONFIG_CPU_HAS_ASID=y
# CONFIG_CPU_ICACHE_DISABLE is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y
CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_PM=y
CONFIG_CPU_RMAP=y
CONFIG_CPU_THERMAL=y
CONFIG_CPU_THUMB_CAPABLE=y
CONFIG_CPU_TLB_V7=y
CONFIG_CPU_V7=y
CONFIG_CRC16=y
# CONFIG_CRC32_SARWATE is not set
CONFIG_CRC32_SLICEBY8=y
CONFIG_CRYPTO_ACOMP2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_CTR=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_DEV_QCE=y
CONFIG_CRYPTO_DRBG=y
CONFIG_CRYPTO_DRBG_HMAC=y
CONFIG_CRYPTO_DRBG_MENU=y
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_GF128MUL=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_JITTERENTROPY=y
CONFIG_CRYPTO_LZO=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_NULL2=y
CONFIG_CRYPTO_RNG=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_RNG_DEFAULT=y
CONFIG_CRYPTO_SEQIV=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_WORKQUEUE=y
CONFIG_CRYPTO_XTS=y
CONFIG_DCACHE_WORD_ACCESS=y
CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
# CONFIG_DEBUG_UART_8250 is not set
# CONFIG_DEBUG_USER is not set
CONFIG_DMADEVICES=y
CONFIG_DMA_ENGINE=y
# CONFIG_DMA_NOOP_OPS is not set
CONFIG_DMA_OF=y
CONFIG_DMA_SHARED_BUFFER=y
CONFIG_DMA_VIRTUAL_CHANNELS=y
# CONFIG_DMA_VIRT_OPS is not set
# CONFIG_DRM_LIB_RANDOM is not set
CONFIG_DTC=y
CONFIG_DT_IDLE_STATES=y
CONFIG_DYNAMIC_DEBUG=y
CONFIG_EDAC_ATOMIC_SCRUB=y
CONFIG_EDAC_SUPPORT=y
ipq40xx: add Cisco Meraki MR33 Support This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-10 09:59:18 +00:00
CONFIG_EEPROM_AT24=y
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
CONFIG_ESSEDMA=y
CONFIG_EXPORTFS=y
CONFIG_EXTCON=y
CONFIG_FIXED_PHY=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_FUTEX_PI=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CPU_AUTOPROBE=y
CONFIG_GENERIC_EARLY_IOREMAP=y
CONFIG_GENERIC_IDLE_POLL_SETUP=y
CONFIG_GENERIC_IO=y
CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
CONFIG_GENERIC_MSI_IRQ=y
CONFIG_GENERIC_MSI_IRQ_DOMAIN=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_PHY=y
CONFIG_GENERIC_PINCONF=y
CONFIG_GENERIC_PINCTRL_GROUPS=y
CONFIG_GENERIC_PINMUX_FUNCTIONS=y
CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GPIOLIB=y
CONFIG_GPIOLIB_IRQCHIP=y
ipq40xx: add support for Netgear EX6100v2/EX6150v2 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
CONFIG_GPIO_74X164=y
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_WATCHDOG=y
# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
# CONFIG_GRO_CELLS is not set
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT_MAP=y
# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
CONFIG_HAVE_ARCH_AUDITSYSCALL=y
CONFIG_HAVE_ARCH_BITREVERSE=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_ARCH_PFN_VALID=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_ARM_ARCH_TIMER=y
CONFIG_HAVE_ARM_SMCCC=y
# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
CONFIG_HAVE_CC_STACKPROTECTOR=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_CLK_PREPARE=y
CONFIG_HAVE_CONTEXT_TRACKING=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_HAVE_DEBUG_KMEMLEAK=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
CONFIG_HAVE_EBPF_JIT=y
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_HAVE_NET_DSA=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_OPTPROBES=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_HAVE_PERF_REGS=y
CONFIG_HAVE_PERF_USER_STACK_DUMP=y
CONFIG_HAVE_PROC_CPU=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_SMP=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_UID16=y
CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
CONFIG_HIGHMEM=y
# CONFIG_HIGHPTE is not set
CONFIG_HWSPINLOCK=y
CONFIG_HWSPINLOCK_QCOM=y
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_MSM=y
CONFIG_HZ_FIXED=0
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_QUP=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_IOMMU_HELPER=y
# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set
# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set
CONFIG_IOMMU_SUPPORT=y
CONFIG_IPQ_GCC_4019=y
# CONFIG_IPQ_GCC_806X is not set
# CONFIG_IPQ_GCC_8074 is not set
# CONFIG_IPQ_LCC_806X is not set
CONFIG_IRQCHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_WORK=y
ipq40xx: add Cisco Meraki MR33 Support This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-10 09:59:18 +00:00
CONFIG_LEDS_LP5562=y
CONFIG_LEDS_LP55XX_COMMON=y
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
CONFIG_LIBFDT=y
CONFIG_LOCK_SPIN_ON_OWNER=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_MDIO_BITBANG=y
CONFIG_MDIO_BUS=y
CONFIG_MDIO_DEVICE=y
CONFIG_MDIO_GPIO=y
CONFIG_MDIO_IPQ40XX=y
# CONFIG_MDM_GCC_9615 is not set
# CONFIG_MDM_LCC_9615 is not set
# CONFIG_MFD_QCOM_RPM is not set
# CONFIG_MFD_SPMI_PMIC is not set
CONFIG_MFD_SYSCON=y
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
CONFIG_MIGHT_HAVE_PCI=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_MSM_BUS_SCALING=y
# CONFIG_MSM_GCC_8660 is not set
# CONFIG_MSM_GCC_8916 is not set
# CONFIG_MSM_GCC_8960 is not set
# CONFIG_MSM_GCC_8974 is not set
# CONFIG_MSM_GCC_8994 is not set
# CONFIG_MSM_GCC_8996 is not set
# CONFIG_MSM_LCC_8960 is not set
# CONFIG_MSM_MMCC_8960 is not set
# CONFIG_MSM_MMCC_8974 is not set
# CONFIG_MSM_MMCC_8996 is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_M25P80=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_QCOM=y
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13 This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
CONFIG_MTD_SPINAND_MT29F=y
CONFIG_MTD_SPINAND_ONDIEECC=y
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_FIT_FW=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_BLOCK=y
# CONFIG_MTD_UBI_FASTMAP is not set
# CONFIG_MTD_UBI_GLUEBI is not set
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MULTI_IRQ_HANDLER=y
CONFIG_MUTEX_SPIN_ON_OWNER=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEON=y
CONFIG_NET_DSA=y
CONFIG_NET_DSA_QCA8K=y
CONFIG_NET_DSA_TAG_QCA=y
CONFIG_NET_FLOW_LIMIT=y
CONFIG_NET_PTP_CLASSIFY=y
CONFIG_NET_SWITCHDEV=y
CONFIG_NLS=y
CONFIG_NO_BOOTMEM=y
CONFIG_NO_HZ=y
CONFIG_NO_HZ_COMMON=y
CONFIG_NO_HZ_IDLE=y
CONFIG_NR_CPUS=4
CONFIG_NVMEM=y
CONFIG_OF=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_ADDRESS_PCI=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_GPIO=y
CONFIG_OF_IRQ=y
CONFIG_OF_MDIO=y
CONFIG_OF_NET=y
CONFIG_OF_PCI=y
CONFIG_OF_PCI_IRQ=y
CONFIG_OF_RESERVED_MEM=y
CONFIG_OLD_SIGACTION=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_OPTEE=y
CONFIG_PADATA=y
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_PCI=y
CONFIG_PCIEAER=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIE_DW=y
CONFIG_PCIE_DW_HOST=y
CONFIG_PCIE_QCOM=y
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_DOMAINS_GENERIC=y
CONFIG_PCI_MSI=y
CONFIG_PCI_MSI_IRQ_DOMAIN=y
CONFIG_PERF_USE_VMALLOC=y
CONFIG_PGTABLE_LEVELS=2
CONFIG_PHYLIB=y
# CONFIG_PHY_QCOM_APQ8064_SATA is not set
# CONFIG_PHY_QCOM_IPQ806X_SATA is not set
# CONFIG_PHY_QCOM_QMP is not set
# CONFIG_PHY_QCOM_QUSB2 is not set
# CONFIG_PHY_QCOM_UFS is not set
CONFIG_PINCTRL=y
# CONFIG_PINCTRL_APQ8064 is not set
# CONFIG_PINCTRL_APQ8084 is not set
CONFIG_PINCTRL_IPQ4019=y
# CONFIG_PINCTRL_IPQ8064 is not set
# CONFIG_PINCTRL_IPQ8074 is not set
# CONFIG_PINCTRL_MDM9615 is not set
CONFIG_PINCTRL_MSM=y
# CONFIG_PINCTRL_MSM8660 is not set
# CONFIG_PINCTRL_MSM8916 is not set
# CONFIG_PINCTRL_MSM8960 is not set
# CONFIG_PINCTRL_MSM8994 is not set
# CONFIG_PINCTRL_MSM8996 is not set
# CONFIG_PINCTRL_QCOM_SPMI_PMIC is not set
# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set
CONFIG_PM_OPP=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_MSM=y
CONFIG_POWER_SUPPLY=y
CONFIG_PPS=y
CONFIG_PRINTK_TIME=y
CONFIG_PTP_1588_CLOCK=y
CONFIG_QCOM_BAM_DMA=y
# CONFIG_QCOM_EBI2 is not set
# CONFIG_QCOM_GSBI is not set
# CONFIG_QCOM_IOMMU is not set
CONFIG_QCOM_PM=y
CONFIG_QCOM_QFPROM=y
CONFIG_QCOM_SCM=y
CONFIG_QCOM_SCM_32=y
CONFIG_QCOM_SMEM=y
# CONFIG_QCOM_SMP2P is not set
# CONFIG_QCOM_SMSM is not set
CONFIG_QCOM_TCSR=y
# CONFIG_QCOM_TSENS is not set
CONFIG_QCOM_WDT=y
# CONFIG_QRTR is not set
CONFIG_RAS=y
CONFIG_RATIONAL=y
CONFIG_RCU_CPU_STALL_TIMEOUT=21
CONFIG_RCU_NEED_SEGCBLIST=y
CONFIG_RCU_STALL_COMMON=y
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGMAP_SPI=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
# CONFIG_REGULATOR_QCOM_SPMI is not set
CONFIG_REGULATOR_VCTRL=y
CONFIG_RESET_CONTROLLER=y
CONFIG_RFS_ACCEL=y
# CONFIG_RPMSG_QCOM_SMD is not set
CONFIG_RPS=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_DRV_CMOS is not set
CONFIG_RTC_I2C_AND_SPI=y
CONFIG_RWSEM_SPIN_ON_OWNER=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_SCHED_INFO is not set
# CONFIG_SCSI_DMA is not set
CONFIG_SERIAL_8250_FSL=y
# CONFIG_SERIAL_AMBA_PL011 is not set
CONFIG_SERIAL_MSM=y
CONFIG_SERIAL_MSM_CONSOLE=y
CONFIG_SMP=y
CONFIG_SMP_ON_UP=y
CONFIG_SPARSE_IRQ=y
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
ipq40xx: add support for Netgear EX6100v2/EX6150v2 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
CONFIG_SPI_GPIO=y
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 19:40:50 +00:00
CONFIG_SPI_QUP=y
CONFIG_SPMI=y
CONFIG_SPMI_MSM_PMIC_ARB=y
CONFIG_SRCU=y
CONFIG_SWCONFIG=y
CONFIG_SWCONFIG_LEDS=y
CONFIG_SWIOTLB=y
CONFIG_SWPHY=y
CONFIG_SWP_EMULATE=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_TEE=y
CONFIG_THERMAL=y
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
CONFIG_THERMAL_GOV_STEP_WISE=y
CONFIG_THERMAL_OF=y
CONFIG_THIN_ARCHIVES=y
# CONFIG_THUMB2_KERNEL is not set
CONFIG_TICK_CPU_ACCOUNTING=y
CONFIG_TIMER_OF=y
CONFIG_TIMER_PROBE=y
CONFIG_TREE_RCU=y
CONFIG_TREE_SRCU=y
CONFIG_UBIFS_FS=y
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
CONFIG_UEVENT_HELPER_PATH=""
CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
CONFIG_USB=y
CONFIG_USB_COMMON=y
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_IPQ4019_PHY=y
CONFIG_USB_PHY=y
# CONFIG_USB_QCOM_8X16_PHY is not set
CONFIG_USB_SUPPORT=y
CONFIG_USE_OF=y
CONFIG_VDSO=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_VFP=y
CONFIG_VFPv3=y
CONFIG_WATCHDOG_CORE=y
CONFIG_XPS=y
CONFIG_XZ_DEC_ARM=y
CONFIG_XZ_DEC_BCJ=y
CONFIG_ZBOOT_ROM_BSS=0
CONFIG_ZBOOT_ROM_TEXT=0
CONFIG_ZLIB_DEFLATE=y
CONFIG_ZLIB_INFLATE=y
Reference in a new issue Copy permalink